G'day people! I live in Melbourne Australia, and have almost completed a Lotus 7/Locost replica using a 2002 1.8l Zetec engine. I purchased the engine/loom/ecu...
Nigel, Initially I used a 2002 computer with my Birkin Se7en. This ECU was complete with PATS. I didn't use the stock harness with the ... It will crank all...
Shouldn't oil flow just by hand turning the crankshaft with a wrench? anthony ... of ... turned? ... there ... suggested ... expects ... key / ... all,...
Hi Anthony - Thanks for the suggestion ... but I doubt it. Because the oil lies in the oil pan/sump which is under the crankshaft etc, I don't think turning...
easiest way is going to be to drain the oil, give it new oil through the head... and put a air wrench on the crank and turn it. But you will not achieve full...
I have a 1995 Ford 2.0 Zetec engine in which I am dry sumping. The problem I have is that the oil filter is part of the oil pump housing. How do I put the...
I have a 1995 2.0 Ford Zetec engine I am in the process of dry sumping. I already have the pan and the pump and trying to determine how the supply line is...
In a message dated 11/15/2006 5:50:29 A.M. Central Standard Time, john.bateman@... writes: any zetec heads in FL? jacksonville here. sounds like mostly...
... help. ... I live up in albany, ga. Most of the people on here are into kit cars and whatnot. I just have a contour with a zetec that I drive every day ...
early zetec's it was. Maybe your not reading his message right? ... From: will cherry To: zetec@yahoogroups.com Sent: Wednesday, November 15, 2006 9:49 AM ...
Hello all, I have a 2000 ZX3 in which the idle has creeped up to @1300rpm. It has the 2.0 Zetec engine and I have been told that it needs the Idle Air Control...
Bolted to the block side of the intake manifold. You might be able to see it from the told but the only possible access will be from the bottom. Even then, it...
John, Lee is correct. It hides under the inlet manifold. Its a round silver metal device that looks a bit like a small fuel filter. Removing the inlet manifold...
Recently my car has been having problems with jerking. It usually happens when the car has warmed up, but it has happened before when it wasnt. Usually low...
manaul I assume? zetecs have a tendency to be some what jerky anyways, gotta be light on the clutch, if the car doesn't ahve full power (not running on all...
Sorry yes its a manual. Ive had this car since I bought it in 98, I know the car jerked a little but this is nothing like its ever done. Its pretty bad at...
CHayse, I assume you don't have any CEL codes (check Engine light) and the CEL light works (lights when you turn on the key)! How old are the plugs and wires?...
No CEL codes are present and I am sure they still work. The plugs and wires were changed about 2 months ago becuase of the problem I was having. The fuel...
I have this same problem with my Zetec in a Birkin (Lotus 7 clone). I have reduced this problem down to the position of my gas pedal foot while driving. If my...
It seems that I can accelerate slowly and the car will act ok, maybe a slight jerk here and there but nothing too bad. However if im on the highway and trying...
I would check the fuel pressure, the fuel pressure sensor, the coils, The Spark plug wires, the throttle position sensor, the Mass Air Flow sensor, and the o2...
With the jerkin problem check your catalytic converter. Tell me does it seem as though you hardly have any power. This problem is easy to diagnose with and...
I had two 2000 ZX3s with the same problem. In the Focus it was a defective fuel pump. Miss and buck at WOT, would not rev past 5000rpm, can be intermittant....
In a message dated 12/9/2006 10:08:13 A.M. Central Standard Time, jimcp@... writes: It seems that I can accelerate slowly and the car will act ok, maybe ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
