The Fiesta centre in the UK seems to sell these: http://www.fiesta-centre.co.uk/performanceparts/kentcamspage2.htm#camfollowers I would image that's 20 Uk...
In a message dated 12/13/2005 10:15:36 P.M. Central Standard Time, homerun86_2000@... writes: Has anyone converted a cam that uses hyrdaulic lifters to...
if it's on a 95-97 2.0 zetec, the later 98 up 2.0 zetec's solid tappets are larger in diameter so they will not interchange. the earlier head has small tappets...
I've heard that some solid lifter heads will accept cams with a lot of lift (over 0.400") without spring bind. Does anyone know which year Zetec's will accept...
Hi Craig, We have had this discussion before, but to recap. The ZX2 engine is an extremely difficult engine to upgrade on the inside. This stems from the VCT...
the zx3 engine is the one the aftermarket of late has "focused" on (sorry, couldn't resist) but don't be scared away from the zx2 motor because of the vct. the...
I have been running a 1995 Ford Contour motor since 1996. I changed the cams in 1997 to a Kent FZ2002. This is a hydraulic cam. Excellent range 2000-7000...
HI Craig, It sounds like you have a ZX1 engine. You might check out Burton Power and Dunnell in the U.K. for help. Both companies deal with ZX1's. I think...
I just 6 months ago bought a 2002 ZX2 and had big plans to modify. "Had" in that I totalled it when a guy pulled out in front of me. The vehicle has been...
nope. no difference. the early '98 ZX2s had a few deferens (MAF wiring, and maybe a few other easy fixes) but your application should work fine. My S/R has a...
Hi list, I am getting ready to install a 2000 Ford Focus head on my 95 Block that has the waterpump in the bolck. What do I need to do to make this work? I...
just get a 2000 engine, the 95 block is a 2nd gen zetec, the 2000 head is from a 3rd gen zetec, two totally different engines. The 2000 block/engine is going...
Thanks for the info, John After receiving your e-mail, I found the following information online ... Starting in 1998, Ford began using variable camshaft timing...
The reason why I am using the 95 block is that what works in the car the new blocks will not work I have tried it. As far as internals, the rods and pistons...
electric water pump ..maybe... ... From: Craig Straub To: zetec@yahoogroups.com Sent: Sunday, March 05, 2006 4:26 PM Subject: Re: [zetec] 95 block 2000 head ...
I'm getting ready to install a serious set of cams in my ZX3. The car this engine is installed in weighs just under 1300 lbs. I have had a couple of people...
n/a , nitrous/turbo/supercharged ? last I checked there was no zx3 that weighed under 1300lbs, so you have a zx3 engine I'm taking it? What are your other mods...
Well, the car is a Lotus Super 7 replica that weighs 1250lb without driver. The engine is n/a via 45mm dual side draft throttle bodies with port injection....
I'm in the process of swapping the twin cam 1600 motor in my Elan +2 for a 2.0 Zetec crate motor. I'm fitting individual throttle bodies, headers, and possibly...
I'd go with crower personally with all the work you have done. Also look into the ford racing focus head, its cnc'd, and has larger valves. I dont think I...
I have a MegaJolt running a Zetec in my Lotus Europa. I used the stock Ford flywheel sensor and all works fine. At some point in time I'll replace the dual...
Since I've had no one recommend the Crane cams, I'm go to use the Crower setup. I've heard good and bad about the Ford head. The CNC machining is not real...
I picked up an almost new set of Honda CBR600RR throttle bodies on eBay. They came with everything from the fuel lines and wiring harness to the air box, air...
Hi Jeff, I have been looking into this (VCT and an after market ECU) for a while as I am going this route and I may have some answers to your questions....
I would like to know what aftermarket ECU's are being used now on the Zetec motor? I know that in the past the Pectel unit was the hot ticket but that seemed...
sct > rest only big difference a true stand alone has over a sct'd pcm, is maybe more sensors, more readings. Otherwise a sct pcm can be tuned for just about...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
