Tried to bolt a Pinto bellhousing to my T9 trans which was delivered today and it didn''t fit. My $5 ebay find was to good to be true. Were there two different...
ive done this conversion,( mk2 cortina not mk1) use 2.0 sierra belhousing from the 2 ltr pinto , yes it is cast iron , other option is contact Burtons in uk...
John The cortina bell (as delivered to Australia) certainly fits because I've done it. You will need the Corty spigot bush which is a perfect fit in the end of...
Maybe 4. 1600, 2000, 2.3, & 2.8. The bolt pattern on the Zetec is the same as the 1600 kent and the 2000 OHC Pinto. The trans side of them may be different? I ...
Tried to bolt a Pinto bellhousing to my T9 trans which was delivered today and it didn''t fit. My $5 ebay find was to good to be true. Were there two different...
Is the gap the same as the 99-00 zx2? My Haines manual lists 2.0l SPI engines and 99-00 zetec, but does not specify the gap for a '98 zetec. Thanks. Damien...
According to my manuals, the British 4 speed (71-72WG) was used on the 1971-73 Pintos with the 1600 cc engine. The German 4 speed (71- 72WG) was used on the...
Thanks Dusty. I must have a different bellhousing. It does have a 1971 Ford part number. I'll look for another one. Any leads would be appreciated (including a...
Now I'm really confused. I'm beginning to think I have a oddball T9. The large hole in the Cortina bellhousing is the same as the Pinto one, should bolt up to...
I just went out to the barn and measured my T-9 and Pinto bellhousing. The hole is 4 3/8 just like your T-9. the top bolt holes are 5 1/4 inches apart, the...
This does help. At least I know it's a normal T-9. I must have a 1600 kent bellhousing. I have not been to the wreckers lately. I'm in San Jose, CA. There...
Hi John, I have all sorts of questions here. Is your original gear box a 4 or 5 speed? What is the length of your original Bell housing from gearbox mounting ...
Michael, The engine I'm replacing is a 1500 Cortina Gt and 4 speed. I haven't had time to take many measurements yet. I do know the T9 input shaft I have is...
Good evening list, Does anyone know much about the water passages around the cylinders, specifically at the rear of the block. In my quest for a bellhousing to...
John, I don't know the thickness, but any 2lt Pinto or Mustang 2, (or 2lt Capri), should have the correct bellhousing (if from a 4-sp). And if you want to use...
http://www.quad4rods.com/ _____ From: zetec@yahoogroups.com [mailto:zetec@yahoogroups.com] On Behalf Of Dane Marable Sent: Friday, November 04, 2005 10:13 AM ...
Hello all, My ZX3 is beginning to idle over 1k rpms and I think the problem is with the idle air control valve. Does it have to be replaced or can it be...
It probably is the IACV. It is best to replace it as cleaning is just a temporary fix (if it does fix it). I imagine the new ones are the same as the old ones ...
Thanks Briggs I got through that time. It really answered my questions about some of the engine combinations. See Ya Okie ... From: zetec@yahoogroups.com...
I'm not sure. I would think you could get it from a parts store. If not, www.fordpartsonline.com or Bill Jenkins at Team Ford in Las Vegas can get good prices....
You can try to clean it, but sometimes they just are too gunked up. If yours is not repairable, try a place like www.autop.com or the like (auto parts search...
Ryan, Thanks for the response. I have decided to replace it instead of trying to clean it. I have use the intake cleaner and a toothbrush in the airmeter of...
Hi group I joined the group about a month ago but just figured out how to post messages (says something about my intelligence). I have a 99 "Hot" ZX2 with...
The Fiesta centre in the UK seems to sell these: http://www.fiesta-centre.co.uk/performanceparts/kentcamspage2.htm#camfollowers I would image that's 20 Uk...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
