Hi, new to the group so hello. Iv put a few pics of my zetec related project in the photos sections for you to have a look at (SS1 zetec folder). this is my...
I just bought a 98 contour with a zetec but it looks different than other zetecs I have seen. It has a part on top of cylinder head behind the cam gears. It...
You Zetec have VCT... antmauriz <antmauriz@...> wrote:I just bought a 98 contour with a zetec but it looks different than other zetecs I have seen. It...
There is a solenoid on the top of the valve cover of Variable Cam Timing (VCT) Zetec engines between the two cam banks. There should also be a corresponding...
great! I'll look for the valve again tonight. Are the ZX2 camshafts and cam gears compatible with my engine? anthony ... Timing ... be a ... gear ... ...
yes, all of the VCT exhuast cams should work. Rob could give you a yes or no, and sell ya one from his store :) ... From: antmauriz To: zetec@yahoogroups.com ...
Thanks for the info! anthony ... yes or no, and sell ya one from his store :) ... Cam ... also ... cam ... as ... different ... head ... is ... of Service....
Tried to bolt a Pinto bellhousing to my T9 trans which was delivered today and it didn''t fit. My $5 ebay find was to good to be true. Were there two different...
ive done this conversion,( mk2 cortina not mk1) use 2.0 sierra belhousing from the 2 ltr pinto , yes it is cast iron , other option is contact Burtons in uk...
John The cortina bell (as delivered to Australia) certainly fits because I've done it. You will need the Corty spigot bush which is a perfect fit in the end of...
Maybe 4. 1600, 2000, 2.3, & 2.8. The bolt pattern on the Zetec is the same as the 1600 kent and the 2000 OHC Pinto. The trans side of them may be different? I ...
Tried to bolt a Pinto bellhousing to my T9 trans which was delivered today and it didn''t fit. My $5 ebay find was to good to be true. Were there two different...
Is the gap the same as the 99-00 zx2? My Haines manual lists 2.0l SPI engines and 99-00 zetec, but does not specify the gap for a '98 zetec. Thanks. Damien...
According to my manuals, the British 4 speed (71-72WG) was used on the 1971-73 Pintos with the 1600 cc engine. The German 4 speed (71- 72WG) was used on the...
Thanks Dusty. I must have a different bellhousing. It does have a 1971 Ford part number. I'll look for another one. Any leads would be appreciated (including a...
Now I'm really confused. I'm beginning to think I have a oddball T9. The large hole in the Cortina bellhousing is the same as the Pinto one, should bolt up to...
I just went out to the barn and measured my T-9 and Pinto bellhousing. The hole is 4 3/8 just like your T-9. the top bolt holes are 5 1/4 inches apart, the...
This does help. At least I know it's a normal T-9. I must have a 1600 kent bellhousing. I have not been to the wreckers lately. I'm in San Jose, CA. There...
Hi John, I have all sorts of questions here. Is your original gear box a 4 or 5 speed? What is the length of your original Bell housing from gearbox mounting ...
Michael, The engine I'm replacing is a 1500 Cortina Gt and 4 speed. I haven't had time to take many measurements yet. I do know the T9 input shaft I have is...
Good evening list, Does anyone know much about the water passages around the cylinders, specifically at the rear of the block. In my quest for a bellhousing to...
John, I don't know the thickness, but any 2lt Pinto or Mustang 2, (or 2lt Capri), should have the correct bellhousing (if from a 4-sp). And if you want to use...
http://www.quad4rods.com/ _____ From: zetec@yahoogroups.com [mailto:zetec@yahoogroups.com] On Behalf Of Dane Marable Sent: Friday, November 04, 2005 10:13 AM ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
