Anyone out there with a 1998 zx2 that they have parted out? I am looking for a CCRM, the module that sits right below the air cleaner box and has lots of...
Mark, I might have this part. I have 2 Zetec engines I want to sell, plus a complete engine management wiring, 2 ECMs, manual and miscellaneous under the...
In a message dated 08/04/2005 8:50:31 PM Eastern Daylight Time, hartmark@... writes: << My the AC clutch isn't engaging and that is one of the major...
They're up to $172 now and I just had to pay them (dealer) to repair a bunch of mouse damage to the electrical system (LOTS of splicing had to be done). I'll...
In a message dated 08/05/2005 7:53:28 AM Eastern Daylight Time, hartmark@... writes: << They're up to $172 now and I just had to pay them (dealer) to...
Hi Guys Thanks for the replies. 3 and 4 pistons needing investigated because of low compression. Some suggest to change the Engine without messing up with the...
Hi Jim Many Thanks for your endoscopic idea, I do that in the Hospital but in the car, may be the probe and the light are different. Interesting to see what is...
The AC in my car is now working. It actually took longer to find and get the CCRM than it did to diagnose AND remove and replace the part itself. Here's some...
Hi FORD ZETEC 1.6L 16V 1996 P Reg I am looking for timing belt, auxiliary drive belt and a Water pump kits for the above. Is there any mail order suppliers...
Hi readers Please help me! I had an engine change (fully refurbished) Zetec 1,6L 16V , I had huge problems with the garage as the bill escaled changing every...
I have a Focus ZX3 about 35,000 miles on the engine, 70,000 on car. This was a Project car when I was running cal-focus.com I have full rally graphics, Spacro...
Hi, new to the group so hello. Iv put a few pics of my zetec related project in the photos sections for you to have a look at (SS1 zetec folder). this is my...
I just bought a 98 contour with a zetec but it looks different than other zetecs I have seen. It has a part on top of cylinder head behind the cam gears. It...
You Zetec have VCT... antmauriz <antmauriz@...> wrote:I just bought a 98 contour with a zetec but it looks different than other zetecs I have seen. It...
There is a solenoid on the top of the valve cover of Variable Cam Timing (VCT) Zetec engines between the two cam banks. There should also be a corresponding...
great! I'll look for the valve again tonight. Are the ZX2 camshafts and cam gears compatible with my engine? anthony ... Timing ... be a ... gear ... ...
yes, all of the VCT exhuast cams should work. Rob could give you a yes or no, and sell ya one from his store :) ... From: antmauriz To: zetec@yahoogroups.com ...
Thanks for the info! anthony ... yes or no, and sell ya one from his store :) ... Cam ... also ... cam ... as ... different ... head ... is ... of Service....
Tried to bolt a Pinto bellhousing to my T9 trans which was delivered today and it didn''t fit. My $5 ebay find was to good to be true. Were there two different...
ive done this conversion,( mk2 cortina not mk1) use 2.0 sierra belhousing from the 2 ltr pinto , yes it is cast iron , other option is contact Burtons in uk...
John The cortina bell (as delivered to Australia) certainly fits because I've done it. You will need the Corty spigot bush which is a perfect fit in the end of...
Maybe 4. 1600, 2000, 2.3, & 2.8. The bolt pattern on the Zetec is the same as the 1600 kent and the 2000 OHC Pinto. The trans side of them may be different? I ...
Tried to bolt a Pinto bellhousing to my T9 trans which was delivered today and it didn''t fit. My $5 ebay find was to good to be true. Were there two different...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
