Ok, since no one is biting, I'll offer both engines, which have less than 30,000 miles each, for $250 delivered within 500 miles of South Bend, IN where I...
I am resending again. Any takers for the parts otherwise off to the scrapyard. Ed It's time to clean out the garage. I have the following items available from...
emdemas:First emdemas...
emdemas@...
Sep 5, 2003 3:17 am
8340
Ok I have rambled through the archives and have not really found a definate answer. Is there or is there not a direct bolt on bellhousing for the zetec 2.0 to...
Hi Bill, All ford 4 cylinder engines built during the past 40 years have the same Bellhousing bolt pattern. The question then becomes the T-5 end of the...
Sorry to disapoint you but ford has more than one bell housing pattern for their four bangers. There is the pinto pattern of the CVH, zetec and early x-flows...
There is a company in Colorado, Quad 4 Rods, that makes a bellhousing to mate the Zetec to the T5. I just bought one for the roadster project that I am working...
The problem is the starter, the T9 is the transmission all the kit car guys use, but you need the starter relocated to work otherwise it just runs into the oil...
The Merkur tranny and belhousing will fit the Zetec, and this is a popular swap in England as there are a lot of Merkurs around although they call them ...
I came across this ( http://www.geocities.com/rmodos/DSCF0011.JPG ) steering knuckle, looks to be from a front wheel drive, definitely a ford part (ford oval...
I'm looking for cams one notch more aggressive than stock for my show off street car (7esque Westfield SEIW) running the ZX2 with VCT (disabled) and Weber 45s....
On my ZX2, the 227 deg / .400 intake cam gave me 0hp gain at 5000 rpm to 10 hp gain at 7000 rpm. The 216 deg / .398 exhaust cam boosted it again - another 6-8...
Does anyone have experience to share regarding aftermarket cams in a SVT head, or aftermarket vs SVT in a ported base Zetec head? Specifically, hp and torque...
I'm considering buying a used Zetec Contour and turbocharging it. Instead of using one of the kits out there, I can get most of the stuff I need elsewhere. A...
i think the t03's i have from when "rodney" was going to make kits are a great one - .048 trim exhaust, .060 trim intake - this is the HKS "super 60" spec. ...
Rob, Is this some form of code or strange language? I tried to fathom it and asked others to decipher it. Maybe this is some esoteric insider code? -Folis- ...
... The TO3 is a good turbo, so is the GT25, and IHI. I happen to have a spare IHI I've been considering using on the Zetec, if/when I get it going. The ...
These TO3 .48 A/R turbine, .60 A/R compressor are common on Thunderbirds from 84-86 (87-88 were IHI), and some Merkurs. I can't remember which is which, but I...
Folis, these numbers are the area ratios of the housings. This will get you up to speed: http://www.turbobygarrett.com/turbobygarrett/kits/basics_index.html ...
Has anyone of this list bought a Focus with the new 145hp Zetec engine? I stopped at my local Ford dealer yesterday and picked up the 2004 flyer and saw that...
john, That is the new duratech. already a hot comodity in the uk and built up in the big horsepower numbers. It is a zero emissions engine. really just a...
Hi Bob, My thoughts on this are, Be Careful! I just got a set of SVT valve springs to try in a stock ZX3 head as an experiment. I am installing a set of Kent...
yep - that's pretty close - tbird turbo guts in a better exhaust housing (the t-birds tend to crack theirs) -I believe it's a Saab style exhaust housing. ...
been selling the duratec, or "pzev" 2.3 in Calif and the Northest since march 2003 - nice motor. It also resides in the base 2WD Ford Ranger. regards, rob...
Rob, I have stopped at the two largest Ford dealers in Richmond, VA, and the only ZX3's they have on the lot have the 2.0 engine. Also, they are not the Delux...
I test drove a ZX3 with a 2.3 and 5 spd. few weeks ago. It is fast and can easily rev. to 6000+ rmp. NICE! K. L.A. CA ... __________________________________ ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
