Is there a leak in the system or are the valves not opening? I'd just replace it all with non-air setup, well worth the aprox $600 for it. -mike ... From:...
At the junk yard today I found a 1988 xt gl. I got the air flow sensor (which is the same as the XT6), dash (where the air vents go), and the high beam switch,...
Snitch456@...
Mar 1, 2002 7:54 pm
6389
I thought that the air folw sensor for the XT6 and XT Turbo were the same and the XT with the 1.8 liter was different. ... From: <Snitch456@...> To:...
James Meyers
jmeyersjr@...
Mar 1, 2002 8:01 pm
6390
$11.00? ... you lucky lil'... :) The bellhousing is the same on th 1.8l as the 2.7 litre... the actual transmission *may* be different, but I can almost...
In a message dated 3/1/2002 3:04:47 PM Eastern Standard Time, ... No, I am driving my XT6 with it in right now and it is fine. But it has to be one out of a...
Snitch456@...
Mar 1, 2002 11:16 pm
6393
In a message dated 3/1/2002 3:14:19 PM Eastern Standard Time, ... ^The four cylinder tranny has fewer clutch plates, so less robust. ^/D I think I will get the...
Snitch456@...
Mar 1, 2002 11:23 pm
6394
Sorry to be gone so long. Got employed again (finally!) and just finshed moving to Tampa, FL (Yukon, it is 20 degrees here too - Celsius LOL). Actually, being...
As for "ground effects", I have an almost complete set of Kaminari aftermarket panels. It was actually made for the XT, but the body is essentially the same....
Hi, I was talking to a friend about my car and it got to transmissions. Mine seems to shift a little sluggish. You gun it, and It revvs before shifting, and...
My XT6 runs pretty hot even after 10 miniutes of driving, I am sure the water pump is busted. How much does it usually cost to get this repaired? (Say at a...
Yes. I'd like to see if anyone might have a message to say about this problem as well because my '89 xt6 4wd with auto does the same sort of thing. it seems to...
ok ya thats sounds great! The front peice I don't really care about cuz the front looks good as it is. I just want it to look lower without lowering it. So how...
There is a technical service bulliten I remember brwosing through describing the slow shifting problems of the 4EAT tranny on the 88- 89 XT6's. I have a link...
... actually they can...???!!! yea actaully they can... don't let tehm boss you around though... because leagally they still have to fix the safty problem...
Hmm... My dealer didn't charge me a cent, and I had it done about a year ago. It took over 6 months for them to *get* the parts though. The parts guys jokingly...
I had a valve body modification done at a local shop and it helped immensely. No more delayed shifts. Cost about $480.00. At least I don't have to worry...
10 year limit? That sucks! So if a family in an XT6 drove off a road and got themselves killed becaus the power steering went out, they can legally sue....
I just read the actual recal. Nowhere does it say anything about 10 year limit. Also because this is a "safety issue" which can cause accident or death I think...
James Meyers
jmeyersjr@...
Mar 3, 2002 7:47 pm
6408
... I ... Let me try this again. I meant to say that if a family got themselves killed because the power steering went out, they CAN'T legally sue. I hate...
I stopped by a meet yesterday (RalliSpec Meet) and a guy (I'm terrible with names) offered me a solution to my valve clatter problem. Mind you, I just had a...
The firstone saftey recall ends in may. Not all recalls live forever. This one only lasted three years with thousands of more cars. ~Phil 1989 Subaru XT6 FWD...
I have a similar problem... but mine goes like this. I put in a new oil pump, seals and belts. I even changed my cam seals while I was down there. After I got...
Clemson456@...
Mar 3, 2002 11:31 pm
6412
Hi, If I find a tape recorder I will record my engine noise. I have almost no valve clatter at all. I use Marvel Mystery Oil with every oil change. One qt...
Here is a page I just found that makes for good reading on this subject. http://www.aera.org/Techside/basicsabouthydrauliclifters.htm I'll also post the words...
where can i get a transmisson for a 91 xt6 fwd. if I can't get a new or rebuilt one can i have it rebuilt, and how much would that cost? Thanks, Jim...
I haven't really thought about how much it would cost. Does anyone else have any experience making urethane molds? I figure I would need to make a wood frame...
