Looking for picrures of any one who has started the XR3. I've had my plans for 6 or so months and have decided to start. But would like to talk with bilders in...
Joe, You would do worse then scanning through the many existing messages. You'll find suggestions for air conditioning, remote camera's, alternate engines...
I have a R&P on hand, and I'm wondering if it will work. Can someone with the Maval R&P give me a dimension by any chance? I need the distance between the two...
Here's a tiny to AC motors announcement: http://tinyurl.com/6fltb5 This system is the sole power for BMW's limited edition all electric Mini. I haven't found...
Tim, It's about 29 inches from centerline to centerline of the inner ball joints on the Maval R&P. Need to emphasize that this is an approximate measurement....
Should also mention that there is very little clearance between the Maval R&P and the transaxle. Discovered that it is necessary to install the transaxle...
http://www.gizmag.com/electric-car-batteries-demonstrate-180000-plus-mile-lifespan/10491/ batteries for the XR3? It would keep from having to replace to...
It looks interesting, however have you seen the TINY diameter of the output, which is supposed to deliver 200HP at 13.000 rpm !!! Also the engine alone weights...
Hi Tim, Thanks for all your work in pulling this information together. I've made a diagram to visualize roughly how these Briggs and Stratton parts fit...
Has anyone considered using a 3cyl GEO Metro/Suzuki Swift engine? If so, anything to share? ************** Stay in touch with ALL of your friends: update your...
So there are 24 teeth, but the information I have on the dimensions doesn't look good: DP 32/64, pitch diameter 3/4", pressure angle 30 deg. As for a different...
Would the fellow that contacted me about frame building and or parts building please do so again. Texas connection I believe. I also have you deep within some...
Hi all, don't know if this has been asked before or not, haven't been able to track down any info just yet. What's the fuel consumption rates on the Kubota...
When I talked to Riley several months ago it sounded like he was working on getting someone to do the bodies. He said the frames weren't a problem. I would...
... been ... I've looked quite a bit, and haven't had much luck in finding anything better than what's already in the files section. For the B&S, there's more...
So sticking my calipers everywhere in the Sachs clutch disk, and reading the spec's from the B&S, it really looks like they may fit together. I don't know...
Hey every one i don't know if this has been posted before but this is a nice and cheap ($20.00) software that can help you design a three wheeler. It lets you...
I sent an email to xr3sales today, December 12, to find out status of frame kits or body kits. I will post here should I ever receive a response. ... working ...
who is the farthest along. Thank you xrminion for your picture of the rollout of the frame. I see at least one person is actually building. Have you found the...
Has anyone decided to use this engine? If so, any information to share? I found one for $250(running) and hope to use it. Have not found any source for a...
Any others here from Idaho? I am in Star and would like to meet anyone else doing the XR-3 in the area. I have started a bit and have located some sources......
I am in Wisconsin and was woundering if there was some sort of listing of where others were bulding. The rt group that i belong to has a map that shows people...
I don't know about using that engine. Its not a very quality engine. There are some honda engines I would use. I think the CRX had a engine that could get...
I think you will find that the quality is very high, this engine is used very extensively as an aircraft conversion with excellent results. Able to run LOTS...
DoNniE&fLenDA, have no idea what your basing that info on the Geo/swift motor comment on..But would appear to be personal opinion which is fine. But there are...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
