Happy 4th back at ya!! I'm in the process of having a new engine built for the General Li - I dropped off the new pistons at the machine shop and am hoping...
Ditto's! Mr Yip, ive been missing your installments of your race days. Been out a while or just neglecting us who like reading up on your weekends? ...
skerocdriver@...
Jul 3, 2004 6:55 pm
15238
Hey guys, since nobody seems to be autocrossing these days, I figured I'd share a bit of my bliss today. Danny from SNS Tuning (the Digifant I gods) was in...
... Oh, sure! Just don't invite everybody, we don't want some of the degenerates from the VWAutox list showing up. ;). Punk. Sure, stop by - on your way to...
... <snip> On second thought, we'll not be there on the 10th - we'll have already left for Nationals. 9th? Planning on being there for both Sat and Sun...
Not sure when our departure date is actually going to be. Gotta figure out how much vacation we can both take. I'd like to run the practice, since it's gonna...
Well, when my new shocks finally come in, I need to get the car cornerweighted. The way the car sits right now, I think the front is too low and the back's...
I will be out of the office starting 07.07.2004 and will not return until 02.08.2004. For questions regarding equity or bond settlement, please contact Line ...
OK - shame me into writing again. I've been busy (changed jobs in January) but I haven't stopped racing. I'll compile a quickie recap of last season...
I will be out of the office starting 07.07.2004 and will not return until 02.08.2004. For questions regarding equity or bond settlement, please contact Line ...
Anybody know the dealer price for the special VW cutaway socket tool for the upper strut bearings? I don't have the Bentley in front of me at the moment for...
... I used a regular 1/2 drive 22mm socket, then ground two sides down flat or so on the bench grinder, near the top. Drop the socket on the nut, an adjustable...
I don't have a clue about the dealer part pricing (Rocky Mountain used to sell the tool). I'm going to get flamed for this but here it goes... Just use an air...
... ..make sure you have the correct spacer/bushing thing installed, too. I recall it being common for the bushing that comes with a lot of strut bearings to...
... about. In all the years I have been buy strut bearings I never did get a bushing. That was always something I had to buy. I replaced a set of strut...
Argh! These spacers/bushings - I think I am missing them or I have the wrong combination. Part of my nightmare with unmentionable tuner... I think it's moot...
... Ahh. Perhaps a 9mm deepwell socket will fit through the 1/2 hole, or maybe chase down a (more $$) 3/4 drive 22mm socket..you should be able to fit a lot...
Hey - thanks - that SnapOn part looks like the correct tool. I ordered a 22mm deep offset box wrench from Craftsman.com (another nightmare)... so I guess I'll...
... That SnapOn tool is for the threaded spacer found in some Rabbits. - Take off 22mm nut (however you get it off, an impact is easiest) - Take washer out -...
... Man, what a thread! I can't believe Frode is missing out on this... ; ) I'm with Rich in TX: Make your own socket. The odds of an offset wrench fitting...
The white washer that comes with Konis - halfdollar sized with a slit in it? It is a vent, so I'm told. When the bumpstop hits the shock body, its being there...
I have a HAZET 22 mm offset wrench that fits down in there perfectly. I forget where I got it from... ... From: <CP1303@...> To: <vwautox@yahoogroups.com> ...
... silly threaded sleeves out without it, but it is not a whole lot of fun.....<<< Same on the A2's, yes. Life is nicer with this special tool, too. As for...
Now I am confused. None of these parts or special tools are required on my camber plates. Shouldn't we be asking why the car doesn't have camber plates?...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
