Hi, I'm wondering what others on this list have used for an engine stand for the narrowcase motors. Is there anyone selling stands, or does anyone have a...
Rob.. European Motorcycle show and SWAP MEET is on the 29th,Santa Clara County Fairgrounds, San Jose Ca, If you do not find one before that, we can keep an...
An engine stand? How sophisticated. :-) I've always done the majority of my engine work on the bench. -- Rick Yamane Yamane Watch Services Fine Watch Repair ...
Lorin, Much as I would like to go, the Santa Clara swap meet is a little too far for me to travel this year. I've looked for a centerstand around here, but...
I have three tires for display/show bikes for the cost of you picking them up or shipping. I'm in San Carlos, CA. One each but they are a matched set.... ...
http://www.motoscrubs.com/Mach1_Engine.htm In the photos at the bottom of this page is some variation of an engine stand that Syd's has. It certainly was...
James Franzen
Franzen@...
Mar 5, 2008 5:09 pm
640
I'm getting ready to tear down my Ducati 160 monza jr engine. I want to make sure I have all the tools I need before I start so I don't get stuck halfway...
bevel250@...
Mar 8, 2008 12:25 am
641
I've got an old Clymer manual for 250, 350, 450 that (I think) has pictures of the special tools. Let me know if someone more knowledgeable than me doesnt get...
-- Howdy I have a scan of the Tools page from the Clymer Duc singles ready to email if someone can tell me how to do it?? bob in Denver ... pictures of the...
I'd recommend an exhaust nut spanner. Some guys will use a punch and hammer on the fins but that's been known to break them off. For tearing down I'll use an...
Go for it Robert! Just "Be careful and take your time." I've helped many guys work on these little gems. THE ONLY SPECIAL TOOL YOU SHOULD HAVE IS THE FLYWHEEL...
Hi Rob I'm sure I have a center stand for 250 ducati single narrow case. I'm in Albion, Washington 99102. I would sell for $40 plus shipping. I have no idea...
Thanks for all the advice. I already have the exhaust spanner and an air impact wrench and I'll spring for the flywheel puller. Already have the Clymer manual...
bevel250@...
Mar 9, 2008 10:01 pm
647
Domi Racer may be of help on parts such as motor lock washers and other parts. If you don't have a parts book they are a good source for this also. Road and...
At 06:01 PM 3/9/08 -0400, you wrote: snip ... Yes, the Haynes manual is very different & contains more, but it covers a much narrower range of models. The...
Darn! I gotta miss that one. It's my Bath-Nite. Gramps ... From: Lorin Guy <loringuy@...> To: vintageduc@yahoogroups.com Sent: Thu, 13 Mar 2008 9:01 am ...
Lorin, Hans, Ed has been trying to email Hans to get a mailing address to send the Motion Pro goodies to. He hasn't gotten any response so I will just bring...
Rick.. We will Call him Monday and go by the shop..WE need to categorize it and log it and assign it to an M/C Thanks L **EuroFest2008 European Motorcycle...
Is anyone in or know somebody in the carpet business, if so I need some information and help.. it would be cool if they are motorcyclists too. Lorin Guy ...
I am www.matsinc.com David "Butch" Cassady Middleborough Mass-a-chu-sets AF&AM, May Flower Lodge Sigma Tau Gamma, Delta Chi house Duck - '65 250cc noise maker...
Easter again and time for the Sunrise ritual ride to the top of Mt.Tam. This ride has been going on for some 35 years now, in the beginning I'm told it was an...
Great report Lorin, thanks. I may have to bail on the show. My Mom had some sort of stroke episode Mon evening and I am not sure what this coming week is going...
Great story Lorin. Sounds like a "Religious Experience." Rich ... From: Lorin Guy <loringuy@...> To: vintageduc@yahoogroups.com Sent: Mon, 24 Mar 2008...
Yikes.. well I hope all is alright, maybe just a wake up call from her body to start eating right and exercise, Had one myself a while back. L **EuroFest2008...
Thanks Lorin, My dad had a stroke last August and got well enough to do limited walking with a walker. He has to be in a nursing home though since he needs 24...
I'm looking for a recommendations for a machine shop to help out with the rebuild of a Ducati 160 monza jr engine. I bought the bike with a bent intake valve...
bevel250@...
Mar 26, 2008 12:18 am
663
hi, take end play measurements. TAKE END PLAY MEASUREMENTS FIRST. Its rather easy just important. A while back I had a bad transmission in my car. I got 3...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
