Hi All If any of you Americans live on route 30 and see a black 1946 rg M21 with sidecar in the next week or so give us a wave my wife Sara and I are on a 5000...
hi everybody. am new on the list my name is douglas from oz. have just assembled the bottom end of my m20 motor, but referring to assembly manual i've realised...
Hey guys...I have a 1940 BSA M20 and I'm just trying to slowly fix up the little things that could be better on it...the only thing is...I'm new to the BSA and...
Dear John, Your 1940 BSA M20 originally had an 8 inch headlamp, as all the early bikes did. If you insiist on replacing it with the smaller one, like if you...
I'm not sure I'm clear on what you are saying. On my bike right now I have a small headlight and I would like a large one. If you have a large one to trade I...
I am going over my bike and I am trying to make a couple things look a little better / more period correct. The guy who I purchased the bike from had used lots...
Doug, Don't know if some one has replied to you off list but the "washer" you are reffering to is actually the crankshaft shim. The cush drive spring...
The short answer is no. Well not from your local hardware store any way. There is two "correct" cable clamps. The original rubber ones that I have not seen for...
I have posted a couple of shots from the web indes to the photo section and have also included a link to Tim Munroe's index page of the images that he took at...
Hi, I had to change yesterday my fabric gear in the magdyno. I refited a new one and I got now a question: Is it needed to put some grease on the gears (to the...
Sacha Romier
sacha.romier@...
Oct 20, 2006 12:19 pm
614
Hi to all,I have visited this site anumber of times since I got my M20 (3 weeks ago)the bike has not run for 31 years,but a very good friend of mine and fellow...
Welcome Gary! I'm Marcelo from Argentina. I'm a proud owner of a 1944 WM20. She run very well. If you need to fix your bike, I've a friend in London who has a...
start by raising your needle position to the bottom notch and see if that makes a difference, sounds like you're much too lean from idle up....then check if...
Someone was advetising tool box straps a while back. I wanted to get some for my 44 M20 but didn't get a rply back about them. Who had them & do they have any...
Hi, Just to say hello, Im just starting out, looking to build a mongrel WM20 from parts or Basket Cases, condition and completeness not too much of an issue,...
hi! my name is douglas from victoria australia. i have amostly there wm20 43' by the frame and engine no. i am willing to part with. it is in mock up stage...
Hi all, After owning my 1941 WDM20 for the last 7 years I find that I haven't used it and shown it off as much as I should have and, because it has always run...
I am restoring a 1938 BSA M-20 and have run into a bit of a problem with the front hub assembly. Someone has apparently assembled it wrongly in the past, the...
I have Just collected my dream restoration project - a real sleeper WM20 from the wilds of Scotland, It has a very early frame number WM20 1435 Which causes a...
Dear All, I am having problems with my gearbox. It gets stuck in between gears from time to time and wont come back out. Can anyone answer the following: 1) I...
Hi Andy, I can just give some general sugestions: - get a plan of your gearbox - In the Hayes book (something like that, I do not remember the name) it is...
Sacha Romier
sacha.romier@...
Mar 14, 2007 6:36 am
665
Hi, Have you contacted Brian Pollitt of the BSAOC UK ? It may be that you have a civilian model, that was commandeered literally from a BSA Dealers showroom at...
hello to all people here in the forum, I´m a collector from Spain, and I´m looking a german militaria, and in special one desactivated FG42 or STG44. king...
Hello José María!! Bienvenido! Here there are friends with BSA M20. Do you have one bike? Regards from Argentina Marcelo jose mª <legionario_28@...>...
Just for a change to a motorcycle related post, I have finally got a decient primary for my 43 WM20. Previously I had been using 2BA set screws to hold the...
