Hey guys! Anyone have a top tip on how to remove the front wheel bearings? I tried hammering one of them out with a flathead and a rubberhammer. No luck....
Get a longer bolt. D0 you have the proper manifold? you don't have a 16mm manifold on a bike w/ a 19mm carb, do you? -M1 ... cracked ... It's a ... (carb...
carbs don't really wear out. I've worked on tons of bikes, vespas, gileras, hondas, etc... on that carb you have 2 adjustments. the air-mix screw on the...
Hi all. I am replacing a cracked intake manifold on an ET3 (VMB1M) motor, and the new one looks like it needs longer studs to attach it. The one I am taking...
I did just that, started 1 and 1/2 turns out and throttle stop turned down(fast idle) but when I get to reasonable idle it just dies, tried turning air mix...
as far as i know everything is stock, 19mm is what i have and what the specs call for, bellows was definately wrong, new one fits great, clamp fits nice and...
i did just that, should there be 2 felt gaskets? i put one on intake pipe per drawings but there was another, slightly larger one at the back of inlet tube...
I am divasimone, from Downey, CA, U.S. I am Looking for someone who can appreciate what I do for a living and support me in it. Whether we turn out to be...
There is only one felt ring and it is not necessary. It goes between the rear of the carb and the manifold bellows ring. It is just to help keep dust from...
Hi, I've had all the lights working for a while but blew a bulb and chain reaction. I want the bulbs to last more than 1 month so I bought the R.T. 507 6v...
Well I just got married! I can't believe it, just last year I was beginning to think i would never meet anyone. I'm 25 already and I thought it was all over....
muriel-berggren557@...
Jun 2, 2007 2:43 pm
31801
doesn't matter which terminal you use - one's incoming from the stator, the other outgoing to your lights. n....
I am in the process of trying to loosen the headset of a 50 special as it is sitting out of line but since I have a rounded headlight this may well be from...
can someone please tell me the sequence of the assembly, and the gearbox. Everyone tells me that there should be gaps between the gears, but this can't be...
The headset is held on with a bolt across the back of it, ie opposite the headset. It can't turn more than a few degrees with the bolt loosened, and with the...
http://www.scooterhelp.com/tips/engine/gearbox.sf.vespa.html http://web.ukonline.co.uk/niall.king/smallframes/engine11.htm There should be wear marks on the...
Pinch bolt that goes in the hole directly under the speedo head. You can see it here: http://www.scooterhelp.com/manuals/service.V5A1T.V5B3T.VMA2T/80.jpg There...
then i'd try taking the whole carb apart adn blasting it w/ compressed air. I've had crap in there that has taken several times of disassembly, blasting, etc....
Hi folks, so I just replaced the o ring in the clutch arm and now the clutch wont dis engage completely. It's not the adjustment. Any ideas? Do I need to...
I had the case apart to put in a new cruxiform and top gear. All went well until I broke the piston rings trying to install the cylinder. (Damn). I had the...
... I think you should, too. I believe the pointy bits on the cylinder wall created by honing grind down the rings so that they form a nice, tight seal. -- ...
... Either some spring isn't back where it should be or something in the mechanism is sticking because it's bent or misaligned? Or the clutch cable is too...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
