Spent some time mapping out the ports on the malossi kit before I cut into it at all. http://www.oopsclunkthud.com/tuning/malossi.pdf Does this match or...
Hi, I recently swapped a 78 ET3 engine into my 1964 V90... All went perfectly but then it all started to go wrong. The engine kicks up 1st or 2nd kick and...
Can't say for sure but I recently changed over to straight cut primaries and mine does sometimes similar things when the clutch is in. I suspect that the cush...
Thanks for the response, I'll have to check that out. I think the noise happens only with the clutch in, but I only rode it a couple of times as it is cos I...
I am thinking about taking my engine case and removing the wrinkle finish. Then, I would polish it close to a mirror finish. I know, I see you shaking your ...
Straight cut gearing that clunks clunks......I put one on my malossi , highly tuned engined with hp4 flywheel, andf the clutch basket flew apart....som maybe...
It did it right away so I am not sure I would see anything. I will be stripping it down this fall to match the ports to the jug as I am happily trying another...
Leave standard et3 crank in, slap on malossi 135 cylinder, reed induction manifold, 24mm carb and pipe? I can't find out much about the induction options for...
We would like to remind you of this upcoming event. Vespa Rochester Open House Date: Saturday, June 4, 2005 Time: 10:00AM - 5:00PM EDT (GMT-04:00) vespa truck...
vespasmallframes@yaho...
Jun 2, 2005 2:02 pm
26364
right, I rode the scoot about a bit, and I get multiple clanks from the gearbox if I have the clutch in and engage a gear. Once I let out the clutch, no probs....
OK, i got the new direct manifold onto my 135 maolssi cylinder, eventually, i just cant figure out how to set the carb up. I think the cable with the small...
Something is not right. it should not make significant noise jostling back and forth in gear. Pull off the clutch cover and have a look. John Collier...
Trying to put together a fast smallframe. I was thinking of ordering zirri Mr2000 cylinder, head, intake and pipe that sip offers. Reading through the forum,...
20HP(uncorrected at back wheel) is hard work to get. you really need to know your stuff. i have heard of people with zirris with only 15HP! mainly because they...
Thanks for the response, that is another one to look at. I realize it will be hard work, but I have access to a quality welder and have a full machine shop in...
not meaning to sound insulting, but so do we (engineering-wise)...and it's still a mission. mr jones here is certainly no dumbarse when it comes to working out...
What is a reasonable number a worb5 modified polini kit, crank, reed induction setup? It seems the numbers I see on the dynos are higher than what real world...
i was really meaning the power fads after heating up . the aluminium is suppose to disspate heat better? i havnt got (or ever run) an aluminium barrel to test...
gotcha. alloy cylinders heat up quicker but dissipate the heat quicker, so you're running a more even temperature top end, quickly. my (alloy) Pinasco 213 is...
We would like to remind you of this upcoming event. Vespa Rochester Open House Date: Saturday, June 4, 2005 Time: 10:00AM - 5:00PM EDT (GMT-04:00) vespa truck...
vespasmallframes@yaho...
Jun 3, 2005 2:02 pm
26379
when the engine temperature increases, the jetting changes. we had a race last weekend. i jetted my scooter in the backyard (100 meters long) and found a 100...
hello, after just fitting my new 25mm delorto carb to my malossi 135 cylinder with the direct intake manifold, i eagerly took it out on the road. It goes like...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
