have you followed the lines everywhere? I had the same problem but finally found where the fluid was pooling under the line leak. If when you are bleeding...
I have experienced no pooling of fluid (or leaks anywhere)?and when I just ran air in the system, I could not hear any hissing of air escaping. ... From:...
What is EZ Bleed? Explain to me your bleeding procedure please. I'm thinking that if your hydraulic parts are OK, then perhaps your bleeding procedure may be...
EZ Bleed is a bleeding system that works off tire pressure.? You hook it to a spare tire, with about 14lbs of pressure, which goes to a fluid bottle.? A line...
OK, that all sounds good. I would suggest following it up with the traditional two-person method so that the master cylinder has a chance to move some fluid...
the "lower" seal in the master cyl. can leak around itself and not show any outward signs of leaking. and I agree with Stefan, that the old fashioned of...
As soon as I can enlist someone (as my wife, the designated clutch/brake pumper is laid up) I will try it that way. Unfortunately I do not have the see-thru...
Michael, I'll go with the air bubble at the top of the line. Old fashioned push/open/close/release works because you force the bubble down the line if you are...
Also try to hold the pedal down and hold it for a minute to let any bubbles float up and into the hook of the line- (once you get some pressure going) - and...
A cylinder hone that you fit in the end of an electric drill is pretty inexpensive. Just be sure to get one small enough. If there isn't any real corrosion to...
... There are tools with two stones and three stones made specifically for brake cylinders. Honing should be done to insure that a new seal seats against a...
The cylinders pit, which means there are low spots where the cup edges won't seal. Honing with any kind of stone you have to evenly take off enough material...
Too bad no pictures. I wonder how long ago and who did the modification? ________________________________ From: happyhelmet13 <happyhelmet13@...> To:...
no no no. Read "a rare auto" to mean a rare autoMOBILE. Not autoMATIC. ... -- -STEFAN http://www.at-speed.com http://photos.at-speed.com VSCCA comp #374 VRG...
Does anyone have positive experience gluing a cracked 96 taillight? It's a clean crack all the way through running a couple of inches parallel to the small...
I've done the honing deal a few times in the past. I found it to be a temporary fix. Meaning that I get a leak of that component again within 6 months. I...
Yes very And BTW there are two on Ebay currently, I will probably bid on the parts car.\ SS _____ From: vSAAB@yahoogroups.com [mailto:vSAAB@yahoogroups.com] On...
Just happened to notice this on Portland Craigslist. Don't know the car or owner. http://portland.craigslist.org/mlt/cto/1107482332.html Andy in PDX OR...
... I've rebuilt cylinders and had them last for years, but they weren't 35-40 years old at the time I rebuilt them, so weren't as pitted as most of what we...
Hi Andy, So you were successful with a bit of honing to take out some very minor pitting? Since it never worked for me very long, mine were probably too...
... Yeah, it is a good car, has barely ever left the island and lives in a cocoon. I was just thinking about that car recently, glad to know it is status quo. ...
... Very secretive owner. Haven't sold him much in recent years. I have seen a couple of pics and it's obvious it's a very nicely preserved example. ...
Bill, Use glue formulated for acrylic plastic. It will 'melt' the edges of the crack and integrate perfectly into the base material. The resulting seam is hard...
Jari Ala-Ilomäki
jari.ala-ilomaki@...
Apr 6, 2009 7:13 am
35271
Ok folks..... not sure what I want to do here... but I've been blessed with way too many old Saab parts to know what to do with, so something has to happen...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
