I took the sonnet to the import wars on Saturday and pitted it aginst all forms of rice rockets , however since I rarely push it as hard on the street as I did...
Sounds like your clutch isn't up to the extra power. You need uprated springs. I think MSS does uprated clutches. ... [This E-mail was scanned for viruses for...
Also it could be a leaky main engine seal. It could be lubricating your clutch. It there is a leak, you would see engine oil dripping from the bell housing. ...
... Is the clutch adjusted properly? That's the first place I'd look. A heavier duty pressure plate? I never had any problem with clutch slippage with a stock...
I've used a MSS clutch on my V4 Rally Car, before that I'd used supposed competition pressure plates and clutch disks but these let me down, the MSS clutch has...
FewingsM@...
Aug 1, 2005 4:28 pm
18856
I think chip has a viable option , and its the age old dilema build somthing , push it hard and you will find the weak point , fix that and new one will...
... A leaky rear oil seal may get oil on the flywheel, where it will spin off against the bell housing and eventualy drip out from below. The clutch side of...
... See Haynes 95/96 V4, chapter 5.9 The bushing in the center (centre) of the flywheel that takes the clutch shaft. (English is not my first language...) -- ...
Just what I wanted to hear... There are many interesting parts coming up on Ebay from across the waves... Last week I got a TPS for the DJet, and I've picked...
We would like to remind you of this upcoming event. Int'l SOC Date: Friday, August 5, 2005 Time: All Day International SAAB Owners Convention. Essen, Germany ...
vSAAB@yahoogroups.com
Aug 1, 2005 10:02 pm
18866
thermostat failure on my 93F race car over the weekend was a real disapointment! anyone have any used "green" thermostats stashed? dented , bent , i'm not too...
All I am saying is that its an easy check and it happened to me. I had a really old seal leak a bunch of oil all over the clutch and it started to glaze over...
... Bill, I may have missed a reply for this, but just in case there was no answer yet: Possibly the bearing race of the 4th gear, in contact with the needle ...
We would like to remind you of this upcoming event. Int'l SOC Date: Saturday, August 6, 2005 Time: All Day International SAAB Owners Convention. Essen,...
vSAAB@yahoogroups.com
Aug 2, 2005 10:02 pm
18872
Jari and David... Thanks! Well, my noise isn't a whine so much as a screech. I've experimented with it and discovered that if I go really easy on ...
OK parts scroungers, Buy one hose - get two. Gates 22209 (CarQuest RBR 22209) is a long, smallish diameter upper radiator hose for some mystery vehicle. One...
... This is an excellent fix for the 4th gear bearing problem. Another solution for the 4th gear needle bearings is to have a bronze bushing machined to fit....
We would like to remind you of this upcoming event. Int'l SOC Date: Sunday, August 7, 2005 Time: All Day International SAAB Owners Convention, Essen Germany ...
vSAAB@yahoogroups.com
Aug 3, 2005 10:02 pm
18876
Does anyone know the specifications for the bolt that holds the transmission in to that rubber bushing (in a 96 v4)? I seem to have misplaced two of them, and...
Hi...Looks like the SOC reg. is closed.......I think I'll be able to get the time off.....too late I guess. Maybe I'll just drive the stroker there on Friday...
Mike St.Pierre
mike6396@...
Aug 4, 2005 4:16 am
18878
... 5/16-18UNC x 1-1/4" or 1-1/2" -- buy both, they're cheaper than making a special trip to get the right one. Yes, it is an American thread, not Metric. At...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
