Anyone in the USA recognise this or the circumstances of it's presentation? http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ViewItem&item=2212619865&category=418 Best...
... How does someone other than Erik end up owning something like that? -- Electronic Voting - If you don't get a receipt, your next election is on us!...
Joshua Pollak
pardsbane@...
Jan 1, 2004 6:32 pm
12129
... The nut on the rear of the pinion shaft, in the gearbox, has left hand thread. ... MH...
... Yes, much hotter than propane. Too hot, too fast for some soldering, but good for bolts etc. Bill...
William Trench
btren@...
Jan 3, 2004 4:34 pm
12133
... I forgot about that one. Too many years since I've had one apart. Time to rebuild another one. I'm in the middle of a job, swapping one out of a '67 V-4...
The reason I ask about MAPP gas is because I have tried EVERYTHING to free the front axle nuts on the Mod 95. I even went to Home Depot and bought a six foot...
... If you're not budging it with a 6-foot cheater bar, you're not doing something right. I've never seen one of these nuts _that_ tight. Are you _sure_ you...
Does MAPP gas set up like a propane torch? Can you use the same ignitor assy? Yes, MAPP cylinders replace propane ones exactly. Keep in mind that all that...
William Trench
btren@...
Jan 4, 2004 12:38 am
12137
... Also has the safety bonus that if you have a leak, you know it right away. J-J...
... doing something ... I've taken apart a few VSAABs now, and these are the toughest I've ever seen. It just will not budge. I really don't want to fry the ...
MAPP does burn hotter, but if you can't budge a nut with a six foot bar after liberal application of penetrating oil, it probably won't help to heat it. I ...
That's the question. I have removed front axles before, but I compressed the spring. On the Sonett, it was so rusted, the whole thing fell out on the driveway....
Sounds fairly dangerous to me.. From the way all the diagrams show it I don't believe it could be done safely. If you want the entire thing (From inner CV to...
... Yes, no problem; but leave the upper ball joint attached to the upper triangle. Just loosen the two bolts of the steering arm and the two lower bolts/nuts ...
It will stretch over fairly easily.. and yes, it's VERY common to remove the half shafts while leaving the spring in place, just as Martin described it. ...
I am looking for the top for a girling master cylinder on a sonett. Mine is kinda of beat up and leaks just a little, so I just don't fill the upper reservoir....
The 96 Stroker (67) is back on the road in regular use as of today. Two things need a little bit of attention. #1 The choke cable was damaged when I was...
... Lubricate the cable inside the sheath and make sure there aren't any kinks in it. If the problem is still there, it might be that the rear pinion bearing...
time for a return spring on the choke. time to show yer creativity on this one! the spedo "skipping"? when the cable was removed , did you get dirt in the...
http://www.lacefield.com/NAIAS2004.htm Sorry, no captions, but I think they're pretty self-explanitory. Yes, they opened up the 9-2X for Steve and I to climb...
... Are those first pictures (of the engine) of the 9-2X or the 9-2? Its funny, it looks just like my WRX's engine bay. In fact, most of the 9-2x and all of...
Joshua Pollak
pardsbane@...
Jan 6, 2004 6:38 am
12154
... Did no one bid on your Sonett when it was up on ebay? I got a spot welder for the holidays, so now I'll be able to fix up my car, hopefully the chassis...
Joshua Pollak
pardsbane@...
Jan 6, 2004 6:43 am
12155
.> ..big hollow boxes filled with about 1000 each ... Where can I get some of those? ... MH...
... T-axle ... I tried that but stopped for fear of tearing it. I know David Nameri has very pliable (silicone ?) rubber ones that he says can be pulled over...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
