Hmm, I might try that. Mine is a bit overdue for cleaning... about 2 years overdue. Z ... -- Zach Leahy Fort Wayne, IN 2006 BMW R1200GS - Rock Red 1992 SHO...
I had a question about these. Is there any way to remove them without destroying them? Per the shop manual, it just says to pull them out, and it shows a...
Pull back the two tabs that holds the retainers in postion, or you will break them trying to extract. I use a c-clip expander. David...
FlamingTaco
flamingtaco@...
Apr 2, 2007 3:50 pm
3254
I have a thread on shoforum about these. Most of them are rust-welded to the retaining panel and/or the headlight screws themselves. C-clip pliers work...
Hartberger, Jason M. ...
hartbejm@...
Apr 2, 2007 5:16 pm
3255
Snap ring pliers Kirk J Doucette www.nesho.com SCT Dealer 1023 Welded _____ From: Ron Porter [mailto:ronporter@...] Sent: Monday, April 02, 2007...
I have a new in box dynomax cat-back exhaust for sale. It's number 17400. It fits a 95 MTX. $200 + shipping. Use this to calculate shipping: Location area...
Edward Mazurek
emazurek@...
Apr 2, 2007 8:45 pm
3258
will this fit a 93 mtx Edward Mazurek <emazurek@...> wrote: I have a new in box dynomax cat-back exhaust for sale. It's number 17400. It fits a 95 MTX. ...
Hi, I don't *think* there are any differences between a 93 MTX and a 95 MTX. But, I'm not positive. Anyone know? Thanks, Ed...
Edward Mazurek
emazurek@...
Apr 2, 2007 9:25 pm
3260
Anyone have any New RUBBER Subframe mounts, (preferably Police) or New engine mounts for a 95 MTX hanging around their garage ?? Must be sent to Tampa,...
We were heading out for dinner Saturday night, and we took my wife's 95 mtx. Look what happened to it.. Bob Bruce 92 w/ a mod or two 95 mtx 100% bone stock ...
Yes, it will fit. It will also fit the Gen1 cars. Dave ... From: v6sho@yahoogroups.com [mailto:v6sho@yahoogroups.com] On Behalf Of Edward Mazurek Sent:...
... From: Edward Mazurek <emazurek@...> ... I just put a Dynomax Gen 2 set on my '90, Black Diamond. The muffler shop did it, not me, but there was no...
I did the same about a week ago! Took a photo, too! http://www.supermotors.net/vehicles/registry/media/497992 ... -- Alex Perry - perry.alex@... 1993...
Okay, so while on subject....... Where's the best place to get a Dynomax setup for a '93 ATX? My entire set up is fading fast!!! TIA! Kris Angermeier ...
When Mrs. VO and I go out, I'm not looking at the odometer, and what's happening is not to the car. :p VO p.s. Hi to Mrs. B. God bless her, she drives an...
Bob... congratulations !!! I also have a 95 MTX, and while you and your wife were celebrating your MTX's 200K... I was sweating and greasy while installing a...
I have 220k on the 93 and I think it's on it's fifth clutch. I dunno I lost count after a while. At least one was changed just because it was apart. 220k 5th...
Are these for 1st gen, 2nd gen, or both? mm in sunny FL From: v6sho@yahoogroups.com [mailto:v6sho@yahoogroups.com] On Behalf Of Hartberger, Jason M. AT2 (AW) ...
Zach...thanks, it gives me a perspective on what to expect. I guess I did ok with my clutch, because there was a lot of city miles on it. When I put the clutch...
Seems like Summit Racing has been mentioned in the past as a good source. Not sure if Dynomax makes an ATX exhaust, tho¹. Somebody else will no doubt chip...
Both. ... Re: [v6sho] Ford Headlamp Housing Retainer Clips Both. wrote: Are these for 1st gen, 2nd gen, or both? mm in sunny FL From: v6sho@yahoogroups.com [...
So I know this has been talked about before but times change and so does the equipment. Give me your thoughts on FRS radios please. We are looking for...
Thanks Alan, I am curious to see what all comes up for info. I need to get this done ASAP. You can hear the exhaust sounding different every couple of days....
