... Wanted to update this. After doing some research I found Service Bulletin Tools-8 (which is also right here in the files section of this group). Lo and...
What's the part number for the tool? To: tmsuzuki@yahoogroups.com From: tbirdsp@... Date: Tue, 3 Mar 2009 23:21:38 +0000 Subject: [tmsuzuki] Re: More '76...
... There are different ones for different models, even different years of the same model (different for RM250/370 A and B models). You will still need a very...
Hey guys, I posted last week, I think I adjusted my chain wrong and cant figure out the proper way to do that. do both sides of the axle loosen? the right...
That's not a nut, that's your axle. I use a phillips screwdriver to hold it while I tighten the nut on the opposite side. To: tmsuzuki@yahoogroups.com From:...
So, do I have to loosen that to adjust the chain properly? ... So, do I have to loosen that to adjust the chain properly? On Sat, Mar 7, 2009 at 8:05 PM, Britt...
Yes, you must loosen the rear axle to adjust your chain, then tighten it back up once you get the proper chain slack. To: tmsuzuki@yahoogroups.com From:...
Would you know if you are supposed to have weight on the bike when measuring the play in the chain? or if the wheel is supposed to be in the air? I just did...
Put two fingers on the upper part of the swingarm between the chain . The Dirt Shack Lee Buchanan , Owner 326 Bamber St. , Mammoth Spring , AR. 72554 ...
First of all the correct procedure is to raise the rear of the bike, spin the wheel by hand and find the spot where the chain is the tightest or has least...
Joe - Yep - those are them - and I still own my 79 RM 125 from then, too. Probably not going to use these, although they are in good used condition - some...
I never could get the Fox airs to work right.....either too stiff or too soft..........the Curnutts sqeaked , but did a good job . The Dirt Shack Lee Buchanan...
Hey Buzzy I went over to a guys house this morning to pickup a freezer and what do you think he had sitting in the corner, A 78 Rm125 or so thats what it...
RICK--mine is a 82 motor in a 1980 rm 125 frame (just got in from riding it in the mud and snow)---all i had to do motor mount wise was grind off a mm or so...
I cant see what he did on the width, the chain look good. It appears that the upper motor mount is a little lower on the Rm than the PE, there is no bolt in it...
RICK THE 82 175 IS A 6 SPEED--i tryed the rm 125 pipe--cut the power in half--the pe 175 pipe is the way to go--but i have heard that the rm 250 is even...
RAY--i know youare aware of the choke plunger deal---and you did check all earths (grounds)--disconected kill switch ?? and no cracked or bare wires inside the...
Sorry; I was not clear will the fuel tank for 79 rm125 fit on 78 rm125 without mods. ... From: wcmsports <wcmsports@...> Subject: [tmsuzuki] rm fuel...
No the tank isn't a straight swap. New front mounts need to be fabricated if you plan to use the tank. To: tmsuzuki@yahoogroups.com From: wcmsports@... ...
RICK---you scared me--was just getting ready to post and ask you if you gave up on the PE engine !!--DOC will know of the top of his head--will e-mail him and...
I HAVE BEEN TRYING TO ID THESE RINGS FOR TWO YEARS--TO NO AVAIL--THEY GO TO SOMETHING A LOT BIGGER THAN A 125--ANYONE KNOW FOR SURE--thanks--buzzymx45...
Yeah - Fox "Air's" - using air would be a pain since it is not inert and reacts with heat to pressure changes, especially the range rear shocks would receive -...
Hi guys I just got an 82 rm125, anyone interested in a trade for either a 125 or 250 air cooled RM or KX? I'm in the mid west, can meet at a race or make road...
Dont know,tried to call him a few times and never no reply.Are you going down to race or spectate.Gonna be upper 50s low 60s there.If your going down 29 south...
I'm racing my 79 250 husky. Wanted to take the tm but never really got around to finishing her up. On the RM I talked to the guy twice and thought we had a...
Well I just wanted to update the group on my progress. This weekend I was finally able to make it down to Dad's shop to do the bottom end rebuild on my 1974...
No extra parts ?? That's not being very effecient . Less parts.....less weight = more effecient ....hehehe mber St. , Mammoth Spring , AR. 72554 1-870-625-0164...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
