Hi all, Does anyone know of any currently available handlebars that match up *bendwise* - exactly *or* closely - with the stock TM125 handlebars (p/n...
Hey phil,you going over to tomahawk for the ralley in 2 weeks.Ray ... From: "phil fuhlman" To: tmsuzuki@yahoogroups.com Subject: [tmsuzuki] TM125 alike /...
To the board I have a situation with a swingarm pivot bolt that is frozen in place to the point where I have drilled two small holes where you would normaly...
I have a '97 RM 250 but I think the engine is a different year. Is there a website that lists Suzuki engine #s? Or does someone know what year this engine is #...
Question for anyone familiar with the 78 RM400C, or 79/80 N or T. Does anybody know if these engines have chronic problem with 3rd gear? My 78 had an on...
No known issues with the RM400 gearboxes but in general most complaints of this nature with any make of tranny is usually 2nd or 3rd gear as these are the most...
Back again with the same problem. I have replaced both cables and the throttle tube and the darn thing still sticks in the wide open position. I have checked...
Did you try starting the motorcycle with the cable disconnected . When I say disconnected I mean take the cable out of the slider put cap and spring back in...
I had an old TS 250 that had the same problem. With mine it was with the carb cylinder where the slide valve operates. If you look at the slide there is a...
I have posted a picture of a BSA frame converted to accept a '79RM125 swing arm and forks. I received this with another bike that I bought. If anybody wants...
JIM----what motor bolts in that frame !!--and what size ??--thanks--buzzymx45 ... From: "Jim" <jsmcquarrie@...> To: <tmsuzuki@yahoogroups.com> Sent:...
Does anyone know if a radial finned head ( aftermarket )was ever made for the early TM/TS 250's ? or if there is any other radial head that can be modified to...
Hello to the "Yellow Hoards".I've been working insane hrs sense "the fork incident",but finally got a chance sunday to disassemble,and examine.the right fork -...
You've bloody well got me worried too now Barry thank you very much! I'll have to back all mine out and hit them up with Loctite and make a few more...
Barry did your forks fall off i seen that happen to a guy in 1975 or 76 fell off in the air wasn't pretty never had nothing come loose so far on my tm 250 yet ...
Hey guys I think we are worried about nothing. If the bolt comes lose the oil leaks out, you should notice that you have no damping in one side of the forks....
The engines are different, '96 came with aluminum clutch plates and aluminum power valve parts, the '97's were steel. I don't know about the motor numbers. I...
I'm putting together a 76RM125 and may not have a decent ignition. I do have an ignition ( Stator, CDI, Coil)from a 79 RM125. Has anyone used a later model...
Sorry for the incomplete answer .Didn't realize you had all components from from a 79 .I can tell you the stroke is different in the 76 vs the 79 .Don't know...
DOC-is the guy----but at present i am using a 1979/rm/125 CDI with a PE 175 1984 ENGINE--lots of extra wires (for the lites and stuff)--but it works better...
KEVIN--i am only using the part that controls the engine--the rest of the electrical system is covered by the wires from the mag. that i am not using--ask the...
purchase a generic universal voltage regulator. one ground wire and one power wire. bolt it to the frame in a convient spot and you're done. no more popped...
Greetings all. I picked up a PE 250 a couple weeks ago and have also ordered a service manual for it which hasn't arrived yet. Can someone tell me which bolt...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
