I was in a Junk yard in Abeline Texas a few months ago, and they had at least 3 peugeots. They also had about 30 older subarus. I wasn't able to get much of...
Not real sure that I get the same "topping off of the tank" on each fill-up as I stop filling when the nozzle shuts itself off, then I take it to the next...
I have parts from the pre-1980 body style changeover that I am trying to find if anyone has a use for (before I scrap it all). I have had several Subies over...
Where are you located Bill? ... From: thegreatsubarubratclub@yahoogroups.com [mailto:thegreatsubarubratclub@yahoogroups.com]On Behalf Of subiewagonparts Sent:...
My question exactly. Need to know how to calculate shipping to Central Texas. I would not mind having a spare fender or two, I have a push bar, but not with...
Very interesting. With the old shitachi, the best I ever got was 280 on a tank. It started going bad and I ended up getting about 180 per tank so went to the...
Bill I'd be interested in the wheels and bar but shipping to Massachusetts may be an issue I ve replaced the front seats out of my 86 with those out of an ...
I need a whole front clip mine is junk(hood, fenders,and that peice that goes under the bumper to tie it all together. if you could find out how much it would...
Was told by some of the Members on the USMB that my tire wear could be due to either the control arm bushing at the crossmember end, or the radius rod bushings...
Interesting. I guess it could be the bushings. I do have a 'wobble' when the steering is unloaded at high speed. Soon as I put any force on the tires left...
I had to replace the PS ball-joint as well as the tie-rod end as both had play in them. Replaced both sides actually, just cause.. My tires appear to be...
Guess it is time to upgrade my wire feed with CO2/Argon mix and get some aluminium wire. Then I can weld on some bosses and mill/drill them for injectors with...
can you wobble your tire left to right? if so check the torque on your axle nuts it is a 36mm nut. if they are torqued to 145 or better and they still wobble...
I've attached a picture of what I think/hope you're describing when you say front push bar bumper. Is that what you have? The white brush guard? If so, I...
Hey Conor, When I saw that message about the brush guard, I thought of you and was going to send an email, but I figured that you would read it too and inquire...
Thanks for the link. That's close to what I'm looking for, but not quite it. I have a gen 1 and am looking for the simple, single piece brush guard that was...
Hi Bruce, Thank you for keeping an eye out for this. I've had a hell of a time tracking one of these down. Hopefully this one will pan out. I think yours is...
... it ... i am not sure which it is as i am new to sub carbs and the brat is stuck at a garage and i will have to describe what to look for i would appreciate...
If it's the original carb, it's probably the carter-weber like the one I have (came off my 82 BRAT with California emissions). I replaced it with the...
my 80 brat has like 60,000 everything works fine.it has a plain iar cleaner on it not the original.so no hoses or anything are there,it was running fine but it...
Could it be a PCV valve? ... From: thegreatsubarubratclub@yahoogroups.com [mailto:thegreatsubarubratclub@yahoogroups.com]On Behalf Of v2snow Sent: Thursday,...
alright there everyone, i have just brought a brand new K&N (cant afford a webber!) that looks the BIZ, and i have put it on the truck, i brought this filter...
No hoses connected to the air cleaner?! It should have at least one hose with a pcv. If the carb is getting oil blown back through via intake manifold, I...
If it fits without the plasticy thing, fit it that way. Is probably just a spacer, maybe to reduce heat soak in the carb. If it has ports or tubes coming...
Just remove the plastic spacer. I did the same thing and it works just as well. I did double up the gasket to be sure of a good seal. I also cut the top of...
