Happy New Near Brat Fans! Quick question for you: Does anybody know what is the best way to drop the oil pan on an 82 Brat (Gen 2)? I have a bit of an oil...
I have an '81 Brat (Gen 1), but my best guess would be to unbolt the motor mounts and jack up the engine. I've had to do that with other types of cars with...
dear conor ive got two 1.6 brat trans one from 79 and one still in a 80 im located in so cal ive also gota couple of wagons that im parting out that are rust...
Before I throw them away, does anyone need a blue interior headliner or a fuel tank for the gen 1? If so, please let me know. Conorj ... Yahoo! for Good -...
Depends on cost and shipping. A gen 1 tank would be nice to have as a spare, but I don't really *need* one. Burt ... [Non-text portions of this message have...
You're in Texas, right? Shipping would be about $70. Cost? Well, I was going to throw it away. I'd be happy trading it for a tail light cover or maybe a 12...
I have an 85 not too sure what is similar on yours but i had to remove my skid plate to access mine. a couple of bolts at the very front and a few at the back....
To remove the oil pan, you'll have to raise the engine up a couple inches, and remove the skid plate. You may just need to tighten the bolts on the pan though....
Hi Tom, I've tightened the bolts before. I know the back ones are a pain because of the cross member. However, at 126K tightening just wont do the trick any ...
Hello fellow Brat enthusiast... Those of you that have installed a holley carb in your brat. I am looking to do the same, so I went to JC Whitney.com and did...
cfm= cubic foot per/minute i think thats a bit much for a little 1.6 - 1.8l 4cyl engine. that engine would have to be rotating at 9500 rpm just to work with...
I have not heard of the Holley carb mod for the Brat. Most folks I know go with the Webber 32-36 DGEV Electric Choke. They say they get more power and better...
DGEV, huh? OK, will have to try to find one. Will either go with throttle body FI or Webber. I really to get the mileage up on this truck. 17-19 ain't...
Thanks for your carb advice. I went ahead and bought the webber carb you described. Although the link didn't work I found the carb you described in a kit that...
Wow, that sure was a quick decision. You're right I don't know your mechanical abilities, what tools you have, or even what year or what shape your Brat is...
OK I wrote a while back with a question concerning my locking cylinder and got a great response as always. (you guys rock)Some one emailed me with a solution...
I'm sending you the wiring diagrams from my Clymer shop manual to your hotmail account. You should be able to figure it out from that. It looks like you...
Tony, Haven't dropped a pan on a Subaru while engine is still in, so I'm not real sure on things, but here's a couple things I probally would do myself. ...
My name is Andrew. I recently got my hands on a 78 Subaru Brat. This is my first vehicle and I would like to make it run as long as possible. The engine runs...
I have a Gen 1 Camper topper i would like to sell. It's in great shape and i'm asking $150.00 Color is white and has working sliding windows and has been in...
So I am planing on going with byb for a body lift and would then like to start thinking about tires, but before I get that far I think you guys would agree...
hey all this is matt i just got my internet back after moveing on new years eve. i have read about 30 posts and the ones that jump out at me most is the oil...
The one here is Austin. IIRC, it is an '83, 4 sp single range, with a drivers door which won't close and a crease in the front fender. Missing a few trip...
Matt, I suppose you could chain the engine from above and lower the crossmember as you still need about 4 inches of clearence between the crossmember and the...
