Hey everyone, thanks for the info...but I can't get enough power to knock the bolt out. I'm beating the crap out of it, but still no movement. Guess I'll try...
To remove mine I heated the parts with a heat gun and then whacked the pin out with a brass hammer. Alex ... From: laotoulrm <laotoulrm@...> Subject: Re:...
quite right Cookie only thing I would add, is that after the Slash 2 (/2) Beemer's , that ended their production run in 1969, came the Slash 5's (/5) Beemer's ...
It probably saved a lot of development work for the Chinese to use dimensions from the BMW 5 series they already knew worked well. I suspect the frame jig was...
The M1 frame was not designed for the OHV engine, and at one time in Beijing to register a M1Super (OHV Model) the owner would have to pull the "mill" and...
Hi, I have a chang with an earles fork. What is the recommended trail for sidecar use/ solo use? The one I have rides well but is a bit shaky when breaking....
I haven't seen a Chang one that is adjustable. Maybe somebody has other ideas but I think you would have to notch the neck to adjust trail. You could also...
I need some pictures of how the M1S clutch lever is set (angle) and the routing of the clutch cable along the engine. Include where the bracket attached on...
Doug, In the toolbox somewhere one of the guys redid thier clutch linkage. I'd be happy to send you a picture of how mine goes, but it really is not well...
Recently found out that somehow my front hub/wheel stop has somehow broken off or decided not to remain on my hub! The result is the hub advancing about 30...
... Hello Doug Do you have a photographie of the shifting plate with the mentioned pin? Same for the acces panel with pin? One of the points to care about on...
... 2008 01:56:41 +0000Subject: [the Chang Jiang Experience] Shifter...thanks! ... Hello Richard Three years ago I got a long hand shifter from Moto Moscow ...
... 2008 01:56:41 +0000Subject: [the Chang Jiang Experience] Shifter...thanks! ... Hello Richard The link I put previously is broken , but you get it this way:...
ah, sorry. mike at blitzbikes.com, it was 12.00 ... From: Stefan Richter <schraube1960@...> Subject: Re: [the Chang Jiang Experience] Shifter...thanks!...
You might try Montreal Sidecar: http://www.montrealsidecar.com/english/products.asp?cat=11 Cheers, Bill ... 2008 01:56:41 +0000Subject: [the Chang Jiang...
Hello friends! I have a question about the rubber spacers or washers that are under the gas tank where the mounting holes are. Mine has a total of 6 rubber...
I'm by no means a guru. Don't even own a Chiang, but just a Dnepr K750. I looked at an illustration in the Changjiang.com place. It shows a blown to bits...
But that is pretty correct. Space it as you need it on top and use a lower to cut vibration. Ask your hardware store for Bibb washers. They are 69 cents at...
Ahhh you are correct and the diagram does show the top two rubber washers stacked. Thanks for your help I just wanted to make sure I had everything in order. ...
Great idea Richard. The rubber washers on my bike are really old, dried out and cracked. Thanks again for your help. ... stack ... washers ... washers ... has...
Has anyone seen a tank shifter kit that is just like the BMW R71? The original R71 shifter seems to come out from under the rubber knee gaurd on the tank....
This leaves too little trail. it makes the rig too twitchy at anything over say 60 kmh. We've been working on an exact copy of the BMW Earles, but as Jeff can...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
