I wanted to introduce myself as a soon to be Chang Jiang owner. After going on a ride with one of the other members (Thanks Fred!) I'm sold. A lot of fun and...
Hi Nick, You sure are "starting out BIG" what kinda deisel ? The 5200 Revs sounds about right for an OHV, I have no idea on aftermarket gears, but the CJ...
Hi All I have just joined your group, I live in Perth WA, I have been thinking of trying to get hold of a CJ. I'm not sure should I try to import or maybe try...
Thank you for the comments, Nick. Would any one have a detailed drawing of the oiling system in the CJ btm end? There must be a simple way to drill, plug and...
Hey Nick here is some info on the oil flow. http://www.changjiangunlimited.com/ff.htm I have seen some other info some where, just need time to search for it. ...
Hello Bill! We discussed this marvelous calender project early this year. I am sure that the durch market will take a few. Say 5 - 10 to be conservative. I...
The font size on my incoming posts and replys are half the size they used to be. It only seems to be happening with the CJ experience and SCT sites I don't...
Tim, I'm looking at a Briggs and Stratton 3 cylinder diesel. It looks like it will fit without too much trouble. Of course, I won't really know how much...
Roy I live in Perth and I have a CJ. If you want to contact me off line I can give you some pointer's on how to go about importing one. I rode mine for awhile...
Hello Nick, Seems as if I remember seeing a diesel in some Russian sidecar bike on one of the diesel motorcycle sites some where. Those Indian Enfield bikes...
Modern engines usually have plain bearings that support crankshaft with a presurized film of oil. To support the load they need a relativly large ammount of...
There's a number of Urals and Dneprs in Europe and one that I know of here in CA. Probably the one you've seen. They look like they've been stretched to fit...
... No..........but, The bikes seem to be similar and have similar backgrounds to some other pictures I've seen on other dealers sites and even on e-bay. ...
I disassembled the petcock and ran a drill thru all the holes and the rate of flow improved 75%. Before the drilling, I determined the rate of flow by how much...
I finally got around to installing the solid state voltage regulator and that was it! The difficult part was trying to figure out where the 3 wires hooked up...
--Actually "lean" out, not "lead" out. Also as it turned out I had no reserve! There was suposed to be a little tube fitted into one of 2 inlet holes in the...
Hi, Talking petcock, I have made a little document about them, will send the link as soon as it is ready. REGARDS GERALD rich102650 <no_reply@yahoogroups.com>...
... Mine also runs lean on the left cylinder because of the petcock. When both lines are removed, it flows fine from the right, but not from the left. Have...
I am also looking for a replacement cb550 petcock. Seen some on ebay, but dont want to end up with one that don't fit. The fuel lines on Alpha look like they...
Hi Rich, Are you going to tell us the exact wiring hook up for the solid state voltage regulator, or, are you going to keep us in suspense. Sooner or later...
After seeing pics of some early tanks, I have to ask. What is this for? I cant figure it out and its driving me nuts. http://asalvatore.com/chang/tank.jpg...
Tony, If you look at the whole tank, it has an air cleaner on top. You connect it to the carburator with a rubber hose giving it a snorkle effect. Here is a...
Hi, Actually what you see on Alpha on that picture is not the fuel line but a sleeve that is suppose to potect the lines from the heat. Now I do not use them...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
