Hey all, Ok, I just want to make sure I am doing this right. I have the new master cylinder, and bench bled it until no air was in it. I then topped it off. ...
Is is possible to remove a ball joint from the control arm while it's on the car? The service manual says remove the control arm and use a press. I have a...
Interesting... several people responded directly, none through the group. Well, the bushings and everything else are perfect, I just installed the complete...
... With the C-clamp style press (also called a 4WD ball joint press), it can be done easily while the arms are in the car. Be careful to use the right bits...
... I ... lines. ... resevoir....THEN ... Once the system is intact and the master cylinder is full pump the pedal several times, keeping pressure on the pedal...
... press ... Once I had the tool, removing and reinstalling the ball joint on a spare control arm took about 3 minutes. Doing it on the car took more like 3...
... I have heard of the proportioning valve? shifting and not allowing the brake fluid to travel to the calipers. I have never seen it. My worst experience was...
I had asked a question before about wheather an 88 wiring harness would be compatible with an 85 car. Well I left the 85's wiring alone. I pulled a 2.2L...
I know this sounds insane but I just experinced thisone my 88 Daytona Shelby Z, crappy gas mileage(25mpg)and changed the O2 sensor and bang, back up to 37MPG! ...
Turbobearcat
Turbobearcat@...
Sep 8, 2004 12:53 pm
11542
Months ago I posted about looking for the part# for my car's radiator , which I did get from somebody but the bad news was it was lost in a email crash(outlook...
Turbobearcat
Turbobearcat@...
Sep 8, 2004 1:10 pm
11543
In a message dated 9/8/2004 9:16:07 AM Eastern Standard Time, Turbobearcat@... writes: so I need to post once more for the part number 88 Daytona Shelby...
alrighty my fine Turbo-Dodge buddies. Tonight I almost wrapped up my 86 T-Top but theres 2 things holding me up. One is frozen brake calipers, no problem I...
ok i am working on an 89 daytona es turbo and the electric fan wont come on. changed the fan no go changed the wiring(because it was cut up) no go. run...
check the relay on the strut tower??? Later, Jay Jochec ... -- -- "....if you got turbo lag, you haven't installed a Gus Valve!!!" Jay Jochec ...
Jay Jochec
Oakley1@...
Sep 9, 2004 4:21 am
11547
Wiring is easy, but still wont work. The computer cant run the 4 wire ais. You will have to switch to a GLHS computer, it will recognise the 4 wire ais. But...
MoparMN426@...
Sep 9, 2004 4:40 am
11548
Matt, Try flipping the pulley backwards. I managed to put my water pump pulley on backwards after doing my timing belt. The pulley was close enough to aligned...
the killer is I didn't move the pump! or the pulley! when I put a new steering rack in and a new transmission i had some flywheel bolts the seezed the crank on...
Well I looked at the car last night... the mounting bracket is bolted to the block nice and tight, and it's still way off. I got a belt on it,was straight on...
anyone in need of any turbo dodge parts? i have a reman mitsu turbo, 2 cars with 4 wheel disc, 2 auto trans a couple computers and so on. i have daytona and...
is the t top car and the hard top windshield the same? ... Do you Yahoo!? Shop for Back-to-School deals on Yahoo! Shopping. [Non-text portions of this message...
Yes, all the glass is the same. I just found out that even the side windows are too when I shut the door and busted it out cause it hit on the C-pillar. Later,...
Jay Jochec
Oakley1@...
Sep 11, 2004 2:24 pm
11554
i got my power steering problem fixed (i was looking at the wrong groove on the crank pulley, and I call myself a weekend mechanic sheese!) I need to figure...
would the master cylinder from and 87 shadow T-1 fit in an 86 Daytona turbo Z? Mine is aparently not happy I decided I tried to use it and is now leaking all...
Hey does anyone have the following items for sale for an 1986 daytona: -Black Trunk Tonneau Cover -Power Door lock switches + motors -and a fog light switch ...
Hey all, Does anyone here have the FSM's for the 85 model year? I need a scan of the 2 pages in the wiring manuals of the 85 FSM, for the 40 way "bulkhead ...
i have an 89' daytona es, 2.5 turbo(garrett) out of a 90' spirit, non intercooled, shows a code 45 which is a fault in overboost shutoff circuit. anyone know...
I have here a very nice 1989 Dodge Daytona ES turbo that I am selling. I have dumped over $6,000 into the engine alone. Mike@Forward motion said that he thinks...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
