i am looking for a t top daytona in the area of western illinois or eastern iowa that is reasonably priced. it doesnt even have to run. just be complete ... Do...
Confirmed. The list has been slow lately, too. I hope it's just because we're all out working on 'em and driving 'em. Tim 86 Daytona 66 Barracuda 03 Ram 1500...
Tim King
TDKing@...
Aug 7, 2004 6:32 am
11505
I need to locate a 1984 or 1985 Daytona Turbo with factory original stripes. David Salamone <shelbydodge@...> is willing to help me and others who...
I took the website down more than a year ago. It was just to much for me to continue. Although, I have been toying around with the idea of putting it back up....
Well after some long hard thinking I have decided to put D&LP back up at half throttle. To get the site back to where it was I will need some help though. A...
I will make the deal with somebody who needs a 523 tranny and shifter, I need a turbo installed on a 87 Daytona Shelby Z, if somebody can install the turbo, ...
Turbobearcat
Turbobearcat@...
Aug 11, 2004 6:04 pm
11510
Maybe - if I could find the time. How far is Lebanon from Akron? Ben http://www.sdacbuckeye.com ... From: Turbobearcat To: daytonaperformance@yahoogroups.com ;...
I am having trouble removing the passenger side/right drive axle from an 88 Turbo Daytona. It just dosn't want to come out of the intermediate shaft. The...
Nate, Butch Nordstrom told me about a fix for this. Drill and tap for a zerk fitting and pump it full of grease. This should push the stub shaft out. Zerks are...
I had the exact same problem on my 89 Daytona Shelby and tried Butch's "fix" and it doesn't work. After countless hours of hammering and spraying PB blaster,...
I pulled the whole setup. Then I rigged my hydraulic floor jack so that it was used as a seperator. This obviously took alot of planning in the interest of...
Once more I post this so here we go again.. 1- 1pce Intake for a Sec gen TI, easy to convert over to TII if you drill and tap and a good one to port. asking...
Turbobearcat
Turbobearcat@...
Aug 18, 2004 5:33 pm
11516
I used heat to get mine apart. Just propane heat on the collar and a hammer. Took a while but it did come apart. my .02 ... from...
I have an 86 daytona with a analog dash and wish to change to a digital dash does anyone have any info on this problem ie:wirring diagrams or have done this...
Folks i am toying with the idea of selling my 89 Daytona that i just recently purchased from Joe Marra. I could really use the money and this may just be the...
I installed a digital dash from an 89 Lebaron into my 88 Daytona Shelby Z, and it was 99% plug&play. Almost all the wire colours matched up, except for one or...
Well after popular demand I have decided to put D&LP back up on a free server for the time being. I have also added a donate button on the homepage so I can...
Hey all, Preparing the final stages of getting my 86 Laser XT back on the road. In the FSM, it talks about "bleeding the master cylinder" before it goes...
Time to clean up the driveway ... too may projects. Selling my 86 Daytona TurboZ C/S. It has t-tops, PW, PL, cruise , air, ect. It is a black and gold package...
Item 2487693452 __________________________________ Do you Yahoo!? Yahoo! Mail is new and improved - Check it out! http://promotions.yahoo.com/new_mail...
... Yes!!! That is, unless you *want* to have to pull it out again because of a spongy brake pedal. What you're talking about is commonly called bench...
black is unburnt fuel. Your oil loss is coming from somewhere else. What do the plugs look like? Later, Jay ... -- -- "....if you got turbo lag, you haven't...
Jay Jochec
Oakley1@...
Aug 25, 2004 1:16 pm
11526
Conquest i/c, 100.00 plus shipping 89 Tona i/c 75.00, pluss shipping Located in San Pablo, Ca. Rodney The Rebirth of MUTT [Non-text portions of this message...
well after several weeks of looking and saving i went and bought a t top daytona.we left at 1030 am and pulled back into the drive at 1100 pm last night . the...
Thanks guys for all the help. I just removed the intermediate shaft with the axle. (though I did not want to.) I was in a hurry to get the engine out. At...
Just want to send out a "thank you" to all who replied. I got a plethora of answers and they all basically said the same thing. Now I know what I need to...
Hey all, Following parts are for sale. Located in Folcroft, PA, 19032 (2 miles from Phila. International Airport). Prices do not include shipping, all...
i am parting out my 88 pacifica so if anyone needs anything let me know. parts that are gone are engine drive axles and rack and pinion. also i have an early...
