Art: If you want a first hand account of the diesel thing. Give Steve Haybeck In Boise ID. An e-mail. He has a diesel motor for sale. stardog2112atyahoodotcom ...
Whilst I know the 5 cylinder / 4 cylinder gearboxes have dirfferent bell housings , does anyone know if the internal gear pairs are interchangeable? Thanks ...
Mark: They are different series of trans. The fours use the 013,(2P,MV) unit. The fives use the 016 or 093 trans. There were no 4 Cyl QSW'S Stateside. Your...
Alas looking for a syncro is futile here in the UK... Audi Quattro is more likely to create a 'Syncro' However, my aim/ idea, was to use the 'innards' of a...
Hi J.B. Do you know much about said swap: "Your looking for a different 5th gear in your QSW? Look for a 5000 Quattro 016 Trans." Chad did such a swap in that...
I have a 5ktq tranny apart, no bell housing or front diff on. Now I have the center diff & transmission left and cannot get the 2 units separated! The 5ktq 5th...
M.S: Stateside there was a 4000-E trans. That came in the 4000 Audi series. It Has a tall fifth gear.0.60 (MV,2M) I would think the Diesel Tranny had a...
Hey Scot, how about shooting an e-mail or call to Chad? I've heard he's pretty opened to inquiries and is well versed on QSW stuff. That Nagaro blue QSW that...
... Last I heard, no, just different animals. There's an entire family of quattro transaxles for Audi 4000,5000, 100, etc etc, and the variety of choices among...
Could someone with the ETKA disk, please look up the CV joint plastic thrust washer part number? I need to order a couple, and can't find a number to work...
I don't know the part you speak of by heart, but here is a washer ("concave washer") that is on the outside end of the CV joint just inside from the circlip,...
...Can anyone describe the symptoms for a bad/worn steering rack? I think that the Utah QSW has a messed up rack. I can watch the end of the rack move up and...
Nate Nelson wrote: The rack and the housing are one assembly. The housing can't move. Its bolted to the fire wall. The rack is internal to the housing....
Couldit be the rack is loose on the steering, or there isa problem withh the damper, or where the 2 sets of steering rods meet and attach, the studs have...
In <BAY114-W183CDE2807FA08C0AE09C3EA170@...>, on 11/13/2008 ... Is there something at that website about the problem that we should watch? I didn't see any...
Here's what I have observed: 1) The rack housing is solidly attached to the body structure. 2) The body structure is not flexing. 3) The bracket that attaches...
Just curious - are you seeing problems/symptoms in handling or tire wear? Dave _____ From: syncronized@yahoogroups.com [mailto:syncronized@yahoogroups.com] On ...
... is worn out or in need of adjustment.? <<< I believe it, too. It ought not to be sloppy that way. Don't know if you can replace just the bushing....
Firstly ignore any advertising attachments on the bottom of this email [if there is any]. I think hotmail may be adding them on. I assume you have power...
I just recently replaced a rack-n-pinion in my '85 QSW with a good used one from an '87 QSW due to a lealing seal on the shaft portion. I understand the play...
Does anyone know the part numbers for the white temperature sensor on the coolant flange, and the one of the back of the head that I think turns on the after...
Does anyone know the part numbers for the white temperature sensor on the coolant flange, and the one of the back of the head that I think turns on the after...
Try 049 919 501B on the water temp. or Bosch 0 280 130 037 on same.two point white.the thermo time switch is 0 280 130 219 in back of head. J.B. in ID. ... the...
The Bosch/IMC parts Manual Gives it as a 2 wire white switch?? The plain #501 shows as single terminal? Whatever! J.B.in ID ... same.two ... head. ... ...
This confusion is interesting. I posed the question, because I went looking for the switch on the lower side of the coolant flange, and reported a bad...