Thanks for the link to the homemade tool for removing the front main bolt. I was a little short of square stock metal in any size. A 2" piece of round metal...
I bought a clutch kit from autohausaz.com but don't recall how much I paid for it. I do think is was less than that, though. The kit did not include the pilot...
I need the following parts for my '85 QSW: -Passenger's side drive-shaft heat shield -Little plastic piece between the vacuum servo and center diff. rod locker...
LDC: Drive shaft heat shield... As in bolted to trans, with three bolts covers the right inboard C/V boot? $5 + postage "aluminum 4000 type" J.B. in ID....
Yep; that's the one J.B. But the one you have is an "aluminum 4000 type". Just wondering, is it 100% compatible to the ones in our QSWs? Reason I ask is that I...
In <g26rr0+1j84@egroups.com>, on 06/04/2008 ... You can make one with 18 ga sheet metal. I cut a piece that matched the flange part, and left enough extra...
L: I have a stack of various ones.+ I have a 016 QSW trans setting in storage. So I will endevour to match one up. No other parts like you listed. J.B. in ID. ...
Sounds good JB. Please e-mail me at ldc007usa@... for mailing and pyament details. So, are the aluminum ones that you mentioned compatible to the QSWs' ...
I replace the broken speedo cable with a good used one while a new one from Autohausaz.com arrived (got the longer cable that eliminates the use of the OXY...
LDC: Don't Know on the alloy ones. The one alloy unit that I have does not fit the 016 QSW tranny. I do not Know how to get the Addy throught the Filter....
Is there any high performance shifter for the QSW 5 speed? Something that has a tight feel, short throws, the usual. Also, is there any 5 cylinder tubular...
034 motorsport sells a nice shifter for the 016 code trans in the QSW. Don't bother with thinking about a header--- no aftermarket company has made one for at...
... Amen. That matches everthing I ever saw about dyno testing on the 4 cylinder Rabbit/Golf engines. The 4-2-1 setup by the factory is very, very good. Don't ...
Thanks J.B. for the parts his sending me. As for answering eletourneau Qs. ... ga sheet metal. I cut a piece that matched the flange part, and left enough...
S.H: Warned you must Be! CIS-E precise it must be. Engine you Pick-up, Labour you will spend. German engineering you will not surepass! Concede you will,work...
For those of us trying to keep our Qs happy, here is a site that looks very interesting: http://www.colorplus.com/index.html Below is a testimonial from a guy...
I've got an 86 that I'd like to sell. Vehicle has 200,000 on it but engine was replaced at 130,000 with one that had 70,000. It runs great. Front brakes and...
Good luck; 99.9% of them were in the trash in 1989 On Fri, Jun 20, 2008 at 8:09 PM, Stephen Haybeck <stardog2112@...> ... [Non-text portions of this...
Exactly! It's the plastic piece that screws under the bottom of the engine compartment. On Sat, Jun 21, 2008 at 5:40 AM, Jon and Christy Weseman < ... ...
Uh-oh. was that important? I guess I need to break out "the book" and look. I'm pretty sure that said piece was gone loooong before I received the wonderful...
Was there a belly panel for the entire engine compartment, in addition to the bottom radiator panel? CP ************** Gas prices getting you down? Search AOL...
One of the fabricators was me, and life grabbed me by the nose and led me around for a bit. I'm trying to clear the garage of my lovely Fox wagon so I can get...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
