In <000101c8ab17$06362b70$9abdf904@David>, on 04/30/2008 ... They get old and brittle and break. But new ones. Unless someone as replaced them before you,...
Speaking lubrication when you get that seat out clean the seat rail grooves - pens, french fries, loose change, pebbles get down in there. Put in a little bit...
CP and Ed, Duct tape did it. Both the front and rear doors' plastic lining had shrunk, loosened up, and the wetness had left a stain on the bottom of the door ...
... They all do that. New, cheap OEM parts and you're set for another 10-15 years. Sure, everybody will be flying about in hovercars, but we'll still be here....
CP, OK, on the plastic pieces failing in the same way. Thanks! On the next 10-15 years, there are still plenty of things to break, improve on my Q, probably...
... I was just thinking of a solar powered fan to circulate air around in my QSW when it's parked. : ) The cargo area seems to get stagnant. Maybe a blower fan...
Solar powered fan, humm. Then I was thinking of a venturi effect (uh) wind generator (over 80mph, maybe) to power my rear lights that have been losing their...
$400 takes the whole thing, otherwise ask about any interested parts. I dont want to have to send it to the crusher. 87 Quantum Synchro Wagon, aka the Dagron...
I belive it is part of the anti surge features of the QSW Gas tank system. It is used to cure vacumme lock and air cavatation under low fual condtions. Mostly...
I saw a bright yellow QW 2 days ago around 6:30pm in PA in the Allentown / Easton area. It was heading towards Easton but was on a different highway from me so...
Barney, Are you still looking for a Syncro diff, suspension, drive-shaft, etc? I know of one that is headed for the crusher pretty soon, but what you want can...
Thanks for the quick reply Barney. If anyone else is interested, speak up. I think this stuff is getting rare. People don't want to crush these cars, but...
It's fun to crush QSWs! ... -- Terrible or not, difficult or not, the only thing that is beautiful, noble, religious, and mystical is to be happy. Arnaud...
While the 88 is running, idle, the ground wire of the fuel pump @ the top of the harness gets warm; I have never noticed that before. Can anyone please check...
I have a 2.2 out of a QSW and need to get the front main bolt out. Anyone ideas how to hold the pulley without the tool the manual calls for? Front and rear...
!/2" air impact gun, maybe put it in gear with the brakes on? I have a bunch of air tools Water pump. Timing belt Valve cover gasket Clutch Slave cylinder. ...
So, NO ONE is driving their QSW and cannot take a few minutes to remove the cover in the back of the cargo are to feel the wiring harness for me? Come on. ... ...
The motor is out of the car (please do not ask how I got it out with the pulley on) pain full lesson. I have impact wrenches, large ones that will not break...
Strap wrench? From: syncronized@yahoogroups.com [mailto:syncronized@yahoogroups.com] On Behalf Of Mike Lein Sent: Thursday, May 22, 2008 11:29 AM To:...
Also to do while motor is out: Both heater hoses/heater core, if they haven't been done in modern times. ... From: Nathan Nelson <nnelson65chev@...> To:...
Scot- I don't know if I went for a long enough drive (only ~5 miles round-trip), but I checked for ya...not even a little warm. -nate ... remove the ... the...
Heater core by its' self s around a 10 hour job, having the motor out will help about 20%. I did a writeup about R&Ring the heatercore a while back, search the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
