So I bought a Barnett clutch kit with springs on ebay for about $160 a while back. I broke the clutch in for about 500 miles, just easy riding. One day I went...
... Gary, You might be right. That said, The slave has a spring in it that if the clutch pressure-plate springs were not there would cause the slave to ...
Joao, Did you adjust the screw on your lever when you put in the new clutch? It sure sounds like the bleed/expansion port on your master cylinder is blocked....
In a message dated 8/1/2007 8:43:20 P.M. Pacific Standard Time, desmo_bee@... writes: Did you adjust the screw on your lever when you put in the new...
... a while back. ........... Should I just go buy a oem clucth (200 bucks) or did I get a crappy clucth pack and contact ... Just general point: if that...
Well I didnt adjust my lever screw, so I think tommorow if I get a chance Im going to check on fariborz point.Im also going to pull my clutch pack out and take...
... No, it won't. It is a hydraulic system, a certain movement of the lever will cause a certain displacement of the piston. Lengthening or shortening the rod...
... not sure if this is relevant, but i have a stock 98st2 with close to 40k mi now, with stock electrics and have not had a spec to trouble. i do run always...
... Tom, As Gary pointed out --if-- the slave piston is bottoming out, increasing the pushrod length will have an effect. I have not checked this on the bike;...
... chance Im going to check on fariborz point.Im also going to pull my clutch pack out and take a peek at it. Make sure it looks okay. It just never felt as...
On my 98, there was a bellows on the release shaft (between the slave and the cases) that was wayyyyy to big for the area that it was crammed into and was...
LiSTers: For those who aren't ale ready aware of this, Motorcorsa in Portland is hosting a three-day Ducati Festival Aug. 10-12 at Portland International...
I should be there as well... hopefully with a few more ducs...an 888 from orcas and a 900ss from seattle just to name a few. hope to see you all there t 99st2...
i have a 99 st-2 only 3800mls it has now when started up the neutral light does not work but after a while it returns then works fine. leave the bike turned...
Lord Hobatz wrote --> Would be good to see some of the PNW bandits at the event or just hooking up and riding up to Seattle on Sunday. <-- I had not planned...
Bhagwan: Come on down to the party. I'll be easy to find as there will be some sort of fence built around the Multistrada too keep the attendees from getting...
Yeah, bring up some Oregonians to keep our WSP/Sheriffs/local cops/Fish&Game busy. We need a break! On 8/2/07, the 'Batz wrote: I've been asked to lead a...
It sounds like you neutral sensor switch is going bad. This seems to be standard fair for all Ducati's, so your in good company. The good news is they're not...
... to be ... news ... Yes, probably easier than the other obvious thing; that the bulb is loose, or a connection dirty. However, if you change the neutral...
John, I also have a '99 ST2 and have had the same issue. The neutral switch I believe is positioned at the right rear of the engine. The wires from the...
I just got back from the shop after having my neutral light switch replaced. I had a slightly different issue. My light would work while the bike was cold, but...
Hi all, I have a lead on a red ST2 for sale, with a bit over 72,000 miles on it. (Located in the United States for our international readers). It also has...
Yeah, I had a go at it when I lost the front end on the 4S a while back. Those wheels would have been handy though. I guess motorcycles are for pussies. Ratso ...
After all of the great reviews of the Avon AV45/AV46 Azaro tires, I switched to them after several sets of Bridgestone BT-020 tires. I even followed the...
