I've seen references on other sites about Sprintex superchargers for boxer engines. Anyone have any more info? Can you still get them? Also, does anyone have...
Hi, I have a pair of reconditioned front callipers of a 1500 sprint Special. Where abouts do you live Nick [Non-text portions of this message have been...
... MMM... Sprintex supercharged Sud sounds good, I'd be interested in that. ... Where are you Mark? Graham ... [Non-text portions of this message have been...
Aun está en pruebas, http://perso.wanadoo.es/jbrunet3/ pero pronto habrá una completa websobre el Sprint, sprintmania.com será su nombre, se aceptan ideas...
HI I have an Alfa Sprint 1.5 twin carb model. The car has been idle for some months, only being started periodically. The last time I attempted to drive it the...
Hi I had the same problem.... I do not think it is a faulty oil sensor, I had that problem with mine but continue to run her over 20000 more kms, then she...
Hi Mark, I hope I am not too late as I am interested in your mudflaps. What condition are they in and how much are you looking for? Regards, Jimmy. ... ...
I have a good condition 1982 Alfasud Ti 1.5. I have just bought a 1983 Alfasud Ti 1.5 green cloverleaf model for parts. Could somebody please tell me the...
You e-mail address is a .au isn't it (damm, can't see that while I'm editing the mail with this mailer), so are those cars Australian models, or the Euro spec...
Just thinking about it some more, I don't think you can simply move the carbs from the twin carb models to the single carb motor. My understanding is, that the...
Hi there, I was said once that the twin carb engines have different cams aswell, so although you'd increase the power of your engine, it'd be not as much as in...
Raul Olchansky
raulsud@...
Jul 28, 2003 2:27 pm
1676
You'd have to swap the heads anyway, the inlet manifolds are different for the single and twin carb models - and if you're going to do that, you may as well...
Hello everybody! First of all I would like to thank you for letting me in the group. My nickname is Jackie and I live in Travnik, Bosnia and Herzegovina. In...
Hi Jackie, Hope we can help you here. Firstly we need to be sure which model car you have. You talk about handbrake and front calipers, but you say the car is...
HI I have a 1986 Alfa Srint, twin carb model. I have recently cleaned out the carburetors. The right side in particular contained a lot of dirt inside it. When...
Hullo Jackie. Regarding your queries - ... handbrake, since there is no any (I don't have a handbrake), is it rope or what? I have new rope which goes from the...
Dear Joan&Graham, I would thank you first for very detailed reply you sent. I have already had some correspondence with Lex, but no answers yet. Huh, where to...
Dear Jackie, Re your reply... ... had some correspondence with Lex, but no answers yet. Huh, where to start from??? First of all, I didn't specify which sprint...
Hello, ... My 1983 Sprint also has 301.98 engine. It is earlier engine with twin lobe camshafts (95hp). The car also has twin Weber carbs, Marelli ingnition...
Hi Gintaras! Thanx for the clarification on engine Nr.!! It was bizarre to have engine which actually doesn't exist! Now on vacuum: I am not a mechanic, even...
Dear Joan&Graham, I will be short this time: my mechanic says that timing belts are ok, as I told you maybe, someone did repairs on engine. I got piston rings,...
Hullo Gintaras, Re your message - ... camshafts (95hp). OK then, that sounds exactly like one of our Sprint engines (1982 Sprint Veloce, 95HP). ... Distributor...
Hello Jackie, ... Both alfasud and 33 have very similar (the same?) clutch. Some people recommend to use 33 1.7 16v clutch because it is better built. ...
Hello Graham, Thank you for the answer. I disassembled distributor and found that wires inside it were badly damaged by oxidation and there was very little...
Some cars have a mechanical advance build into the distributor (base plate rotates and is regulated with a spring) and does not use the vacuum takeoff on the...
Hi everybody!!! Last night I was at my mechanic, and we dismantled the head to check the valves. Guess what! There are no seal caps on exaust valves! Any other...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
