With a new adaptor, would you need to adjust or replace the charger? I am very interested in this, since none of the public charging stations in my area work...
you dont need to change the charger. The j1772 standard is just an ac power delivery system (a plug.) http://www.tucsonev.com/ Â they have several and it will...
7457
Wolf
wolf@...
Sep 2, 2011 2:29 pm
This post reminded me... Is anyone going to Jack's "ev con"? it is near Saint Louis. My dad was trying to talk me in to going... But it is way on the pricey ...
It appears I have broken my transaxle on my 98 Force. Has anyone changed one of these out and know if I need a specially made part? If so, is there any...
Michael Guilford: The only experience I have had with my 1992 Force was worn out CV joints. The mechanic looked all over for a replacement without success. ...
solectria may sell you a new transaxle. i have seen new ones installed into projects. how do you know that is the problem? what did you do so others can avoid...
According to the non-ev mechanic that looked at it and knows this car a bit, he said my CV joints are OK. I can hear the motor whirring away when I step on...
solectria means azure dynamics clunk is good! a bump is way better than a grind. (some like both together best... oops sorry wrong topic) others have heard...
still seeking info for those six wires... orange pink! blue purple (voltmeter oscillates between 12v and 0v every second or so) red (voltmeter reads 12v out) ...
what do those lights mean please. they are on a small black box, driver-side rear above the charger. (connected to the charger... the idiot lights.) - green...
SOUND LIKE A GEAR OR ANOTHER PART OF THE AT1200(TRANSMISSION IS BAD ) ... From: "Michael Anderson" <michael.anderson@...> Sent: Friday, September 02, 2011...
Before you purchase a new transaxle, you might want to remove the motor and make sure that the drive gear and it's retaining parts are still in place and...
Either way (a new tran or fixing it) requires you pull the motor trans and take it apare. Nothing to lose. It sounds like the pin sheared off and the gear...
The stock shaft lengthened by Solectria/Axure: It was cut, and the ends were slipped into a steel tube and welded. When my passenger side shaft broke in my...
Have you tried the files section? Both the service manual and the owners manual are in the files section. All of the leds on the box are controlled by the...
in the files section of the solectria force yahoo group. Download the 98 solectria force service manual. It has a step by step for R&R motor and trans. Â ...
This is a concern that woudn't bother me on any other car, but here it matters. Even with the parking brake pushed down firmly, the dummy light (brake)...
Check the Geo Metro forums and or search for the problem with metros / swifts. I found something similar on a '95 traced to a bad fuse connection under the...
check out photos I made from June 2007 when I replaced my gearbox. It wasn't hard but did require care and attention. Doug Jackson adjackson3.org p.s.: If you...
Hmm. I just checked my 97 Force and the parking brake lever doesn't affect the brake lights -- just the dash indicator. My light has flickered from time to...
Check your break fluid level in the master cylinder. There is a little float in there that sets off the light when it's low. Are you sure it's causing the...
Well, I'm not totally sure. If I take the parking brake to the switch threshold which is up quite a ways from totally down and wiggle it, the brake dash...
Some years of Geo Metro, the lights go on during the day unless the brake handle is up (emergency brake on). The problem I had seen (on a '95 Metro, not a...
Sorry I misunderstood I thought you meant the red break on the. Dash not the daytime running lights. Should be fairly easy to bypass the deity to disable the...
Steve and all: The Daytime Running Lights (DRL) on a Metro can be disabled as follows: 1) Locate the DRL box way up under the dashboard, just right of the ...
Your charger is ok and does not require a change for level 1 or 2 charging. An adaptor is required because of the j1772 standard. First the connector is...
I bought a set from these folks last November. Â Cost me about $2,900 for a set of 13Â KEN BEAL Phone : 410-768-6200 Email : beal190@... BEAL INDUSTRIAL...
