>>A locker and some nice tires will get you a lot farther for he same cost (or probably less $) than a solid axle with open diffs<<<br><br>I second...
>>our borring chat room!<<<br><br>you've never posted anything here before (?) and when you do post something it says;<br>"come on BOYS lets ...
Has anyone seen this GM concept truck? It says it can fit a Twacker in the bed. Who needs a tow? Just load it in the bed and you're ready to go.<br>I just ...
I have 5" of lift but it's just not enough..I need more articulation, I want to be able to lock the front annnnd lift it more....31's just aren't my cup o ...
What gearing? 33's with a 1:1 high range might not like to go uphill on a freeways at all...<br> You could allways just buy a sami and do a SPOA +2" body lift...
blew my head gasket this weekend and needed some opinions. my tracker is a stock 90 4wd with 126k. wanted to play in the mud and got a little stuck, spent...
I've got a 2 inch suspension and 3 inch body, I want to get the new grp tranfercase gearing; 4:1 lowrange.. do my axles with 5.83's...I think that should be ...
Were you reving your engine like mad???<br>I wtched a 98 tj a couple of weeks ago blow his...man that engine was screamin..he musta thought if he reved it high...
I've been doing a little interior work myself. But I prefer the cheap way, since I may as well not spend a lot on my Kicker. Just paint some stuff, its not...
>redeye wrote:<br>>Were you reving your engine like mad???<br><br>These little engine seem too be able to take the revs. I mean, you can toss it 4low,...
I am still having fuel problem with my 91 Tracker. I have found wiring schematic for 91 Suzuki Sidekick, would it be the same as Tracker?<br>Thanks,<br>Art...
Did you say buy a sammy? How dare you! lol. Why would we want to look like everyone else on the trail or street.<br>Anyway, the only way to run 33's w/ that...
Kicker_92: Are you using leaf springs on the front axle and are the shackles on the front or rear of the springs? I found that if you use a 3- or 4-link setup...
Newer jeeps have the pumpkin on the wrong side. I think a cj-7 front end would work and is close to the same width. Forget about cj-5's though 'cause there ...
i kept the revs lo, tried to creep out. spinning the tires just dug a deeper hole. i'm having the garage that swapped my timing belt do the work. i'll check...
My slipyoke in my configuration only moves about 1/2" from full droop to compression. I build the four parallel links and panhard setup to account for this. ...
>>i kept the revs lo, tried to creep out. spinning the tires just dug a deeper hole. i'm having the garage that swapped my timing belt do the work. i'll ...
I'm not sure if both are the same as far as the wiring goes, but I do know that there are differences between Canadian and Japanese models, especially when it ...
Depends on the clutch and if you do it yourself.<br><br>if you DIY and use a Centerforce, it will be about $300. A stock replacement will be between ...
I'm here on and off. <br><br>We just got back form the SEMA show and I think we're going to be able to get ConFerr to get back into the skidplate business for...
Thats good news. They did produce a tranny and transfer case skid as somepoint, didn't they? It would be nice to also see another option for axle trusses for ...
>>We do have the OME 1.5" springs for $59 each. <br>Also, our 1" coil spacer lift is $38 a pair.<br><br><br>Is it safe to run the OME springs with the...
Plus I already have the coil spacers. So the 2.5" in the coils seems too much for the stock struts... Any cheap alternative strut that will accept the addded...
Actually, the OME springs are only 1.5". When combined with the coil spacers, you get 2.5" all together.<br><br>That would be a bit long for your stock struts...
