I am having a difficult time with the speedo gears at the front tire. It seems to keep seizing up to where it doesn't rotate with the tire. I have purchased...
overtighting the axel nut will not let it turn wolfryder ... From: webmailforjames <webmailforjames@...> Subject: [shovelrider] '81 Shovel Speedo To:...
... I just had a similar problem. Bike started fine, ran fine. It started to rap when it got hot, 10 to 20 minutes. I had put a clean screen in in spring. I...
OK, I am going with some T&O 4 4/8 wheels in my 70 FLH, I also want to go with a JIMS oil pump and top end oiling upgrade. What I am woundering is can I take...
Every you all post somthing ,problem , I seem too have one, I put a new clutch in last week 200 miles ago steel plates ,fiber plates and heavy duty springs...
sounds like you have to put a little more pressure on the pressure plate! turn each nut in to approx. 9/16 th of an inch measuring with a ruler from plate to...
Seeing as your front wheel speedo drive is on the side of your axle that just clamps to the fork leg, you just need to loosen up the two nuts enough to allow...
... plate! turn each nut in to approx. 9/16 th of an inch measuring with a ruler from plate to outside of stud. "each to make sure your even all around! from...
Also check the clutch drum & clutch hub themselves & look at the bars (plate guides)on the drum & the slots on the hub that the clutch disks rest in for...
I Have a 79 FLH Minus a lot of extra crap The speedo took a shit a while back Replaced the 1to1 speedo drive new cable,the speedo turns be hand and moves well ...
I'm hangin in there, its been three weeks from my neck surgery and I think it was a success. No more numbness or pain in my arms. Downside is I can't work or...
I know what you mean. I rolled my tractor on May 10 and tore up my shoulder.Then on June 5, I had my shoulder fixed.Summer SUCKED till 2 weeks ago. I can now...
Got her fixed ,tightened up the 3 nuts on the hub ,my goodness ,thats heavy duty springs ,I re adjusted everything,little tuff too hold in for a while but no...
Hello to All I live in G.B and I am considering a deal with a fellow that has a 77 Electra Glide. He has expressed an interest in swapping me for my 2000 FXDX...
Prop the front wheel up, spin it and see where the failure is. Make sure the drive is turning. Its easy enough to tighten everything up with that little tab...
... Your right, but in construction, telling other people what to do doesn't feel like work. I went back to work too soon after my knee surgery and now my knee...
That is unlikely to be an FLT engine since FLT wasn't introduced until 1980. However, the rear belt drive was introduced in 1978 on FX models and some Electra...
Hello Rob, thank you for that interesting information! Im glad to hear that it is an Electra Glide, as this does mean a lot to me. My FXDX is a fine machine...
... 77 ... 2000 ... the ... is ... ViewItem&item=290252162704&_trksid=p2761.l1259 ... just had to be exact. Bein as how its more than 30 years old theres no...
can someone tell me the way to adjust my pushrods on my shovel.are you to adjust them when the tappets are all the way up or all the way down.they are solid...
This subject has been covered here quite a bit over the years. While you are waiting for a response, try clicking on the messages button of the club sight and...
... hear ... is ... and ... first 6 ... before it ... 80 ... frame. The ... stock.The bike ... seller ... a 77 ... 2000 ... prospect the ... this is ... ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
