I think you could probably use the Jim's 6 speed in that case if you can buy it seperately. The problem is the maindrive gear and output is hard to source for...
80 t0 85 mainshaft is a possiblity for clutch hub or go aftermarket.The 5th and output gear would take some research.Belt to chain spocket to retain chain...
Reminder from the Calendar of shovelrider
http://groups.yahoo.com/group/shovelrider/cal
Monthly Meet Shovelriders MC
Saturday September 4, 2004
10:00 am -...
shovelrider@yahoogrou...
Sep 4, 2004 9:40 am
1654
Reminder from the Calendar of shovelrider
http://groups.yahoo.com/group/shovelrider/cal
Open Meeting ALL motorcycles
Sunday September 5, 2004
10:00 am -...
shovelrider@yahoogrou...
Sep 5, 2004 9:40 am
1655
to the LIST- to help finance other projects and to replace my aging dodge pick up, i am reluctantly offering my XL 1200 for sale. its a 1993 with 16hundred...
Fritz, are you looking at adding a Supercharger to your bike? NOS ... From: Fritz To: shovelrider@yahoogroups.com Sent: Wednesday, September 01, 2004 4:24 PM ...
The thing about the 6/4 is that the mainshaft diameter changed from `89 to `90, and all the 6 speed shafts are ground for the later size, apparently Jims has...
Just thought I'd put out an invitation to the group for a Yahoo based Fantasy Football league I came across. The group is intended for Harley riders and is...
Can anyone advise me on the procedure for rocker box gasket replacement as mine are leaking profusely. The service manual don't say shit about this subject. Do...
Can anyone advise me on the procedure for rocker box gasket replacement (FXS 1980) as mine are leaking profusely. The service manual don't say shit about this...
Ask jb about fantasy groups and I'll agree with him? Shovels or football-----HMMMM......--- In ... you'll ... you ... if ... group ... this ... worst...
For my EVO geezer glide maybe.Too much compression on the stroker.--- ... research.Belt to ... good to ... gear ... long ... my ... who ... only.Billet ... it ...
Ok, you guys. You had told me there was no meeting going to be on this day since it falls on a holiday and it would fall onto the fallowing weekend. Well, for...
whaddafrukk is a 6 speed when ya cant rev much past 5500rpm.? you guys with serious engines , sounds good. but i dont wanna shift all them times. i would...
... If it is the gasket between the head and the rocker box you will need to pull the head.But if it is the rocker shaft gaskets you just hold one end with a ...
keith robinson <dad06514@...> wrote:i remember reading about the 5 speeed and comparing the ratios when they first came out. top ration was about the...
My 81 FXEF has the dash mounted tach/speedo pod. The damn tach has gone bouncing (needle jumps all over) The tach that was on the bike when I got it was sort...
I'm running a 4 speed (FX)with the 2.44 first gear, 24t tranny sprocket and a 49t wheel sprocket. Have to slip the clutch a bit from a stop if 2 up riding,...
... BUMMER!! I have a 81 so here's what I know. If you don't want to remove the motor from the frame to remove the rocker boxes here's the other way to do it. ...
Yo, does anyone know why my manual showa a thrust washer between the gear and the starter housing. None of the parts catalogs show one. I can not find one on...
Well if you can resist the new bikes, ask the parts man for a "thrust washer, PN 31502-65. This is installed between the gear and the cover......what the hell...
Oh sorry, I think it is geared to make 6.5 to 7 at 5 grand, not much. I built the bike for a customer, and installed some other blowers for him, he was a...
Rich, using a five speed with the same final drive you have now would fix your drivability problems, and give you much better acceleration through the...
I can go 7000 then the rev limiter kicks in(thank god), I don't doing it often.4 speed & 5 speed are direct drive out the trans.The advantage to the 5 speed is...
The number one thing NOT to forget is to buy a 60 degree triangle (30/60/90) and use it to square the intake spigots as you tighten the headbolts. This helps...
It is a brass thrust washer HD part number 31502-65. Without it the bendix travels too far and you risk damage to the bendix and the outer primary housing. ......
