There are two plugs that you have to take out on the outside corners of the spoiler itself to access the screws that hold the outer corners to the trunklid....
Leigh, I had a quick question. Those progressive softer bump stops that you mentioned before. Where would I be able to purchase them? I was also wondering if...
Roger, try contacting strut manufacturers, like Koni, Tokico, or KYB. If they don't supply them, they might know who does. I think that our cars are too 'low...
Those would be 8mm BTW, and yes, use a deep socket. If yours is lucky enough to have the thin rubber washer still intact, keep using them. The idiot who...
Leigh and Avalon- Thanks for this information. I've located all the screws. With the two screws that are on the exterior ends of the spoiler, is there a nut on...
Ray, the screws at the ends are threaded into plastic clips in the sheetmetal. -A-, I didn't have any rubber washers...are they between the spoiler and the...
The washers are very thin, adhesive on one side, and prevent the moisture/water that is passing through the thin gap and/or water channels FROM entering the...
Nope, I didn't have those washers. I had to rebuild the water channels after gutting, rust converting, and re-filling all the rotten/rusted material with PL...
I went to buy a new thermostat for my 88 Maxima today, was looking for a 195 degree one, but the guy at the autoparts store said the specified one, and the...
The 170 degree t-stat should be fine. That's what mine is. The FSM, nor the Nissan FAST parts lookup software state a temperature for the thermostat. The...
Thank you. I haven't tested the old one, but the engine's been running hotter and hotter over the last several months. (much hotter than in previous summers.)...
The water channels were in the spoiler, not on the trunk lid...? Your spoiler was metal? Mine were all polyurethane. Addco said they were sending me the...
My spoiler was polyurethane, but there is a metal reinforcing strip inside that the studs are welded to and that the screws screw into. And no, there were no...
That's another thing I can't figure out, why the hell they put in a whole kiboodle of washers when all you need are two on each sides!?! Man, Addco is really...
Hey, how long did it take for you to receive your stuff from Addco? It's been three weeks!!!! -A ... a ... sides!?! ... washers ... 2 ... training ... kit. I...
black 88 maxima se 5 spd, new struts all around, new tires all around, reverse glow gauges, K&N drop in filter, recently did a full tune up, trans should be...
I'd give them another call. I got my stuff in a week, to Canada! You need all the extra washers to support the bushings properly. I noticed in Sarin's pics...
my car hasnt been starting...it stopped starting back in april and i kinda just left it there..its atempts to start but it dosent turn over...i remember...
to fit my 87. I splurged on myself considering my birthday is on 9/11 (yeah don't tell me). The set cost $300 (includes the sales tax, damn Arnold), but they...
I got the bushings finally, have yet to put on the sway bar as I believe the stud that came with the kit is way too short!!! I can see why Sarin chucked the...
New spoiler from the dealer - about $800CND (shipped from Japan in Shiro White- great, mines not white anymore.) Kaminari OEM style replacement - about $250 ...
I checked into this some what at a TorontoMaxima meet where there was a 3rd gen with this mod. Some rough measurements revealed that our grille is too narrow,...
I was wondering if anyone has had problems with fuel injectors and if so what are some symptoms...because my 88 max is running like crap and i think thats...
... WHen I bought my 1988 Maxima in 2001, the previous owner told me that there was a recall on the 88's because of the fuel injectors aroudn 1996 and that he...
Hate to sound like I am beating to death a subject that I know has been posted before. I have the headlight problem again. Found a used headlight/turn signal...
... I'm loving my mileage. My girlfriend's Catera is a damned pig. She has to fill up (18 gal) nearly every 4-5 days with her commute. I'm getting about 10-12...
I gave the guy the design, He said he could tweak it abit to look better. Later on he got sick. I went back to talk to the head guy and he stated that the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
