I removed the dash from my 86. I'm looking to reinstall a simple AL one. I can't seem to find any pre-built dashes, so I was going to have one bent for me....
If you don't absolutely _have_ to have AL, you might try: www.florida50.com They have everything from fully wired panels with your selection of autometer...
Florida 50 brings the bling, but unnecessary for a race car. Hoerr Racing and a few other vendors sell pre-cut aluminum dash panels if that's what you're...
I "cheated" and put aluminum over my stock dash, and replaced all the gauges (but left the heater controls and vents). Then didnt like the shiny aluminum, so I...
Perception is a strange thing. I always regarded florida 50's approach as a "poor man's" approach. Not that their prices were so low or anything, but that...
... I thought about using these guys -- for about 30 seconds. Problems I have with these guys: 1 - The plate is 0.25" think -- WAY too think IMHO. 2 - They...
Scott, That's also one of the things I like about florida50. The ability to mount real gauges, in a clean cluster, in the stock dash, with a more-or-less...
here was what i considered a non-blingy florida50 panel: http://www.florida50.com/user/cimage/P1060879.JPG or, as a blank to put your own instruments in: ...
Hi Scott, I'm with you on the stock dash look and would have liked to have the opportunity to creatively gut the stock dash and keep the parts I wanted. But,...
I sent this to my other list, and meant to send it here, too. Thanks! ... From: Peter <pcrussell50@...> Sent: October 10, 2008 11:10 PM To: Fordnatics...
I have been towing my Mustang(3500 lbs) with my own car trailer (1200 lbs) with my 1994 half ton 5.8 E4OD 4x4 for years but if you look at U-cant-Haul they say...
Look at F-250 for Ford......D 200 for Dodge......C/K 20 for Chevy ... From: "pcrussell50@..." <pcrussell50@...> To: rrax-mustang@yahoogroups.com Sent:...
I almost never post on here but this is something I feel reasonably knowledgeable about. I have also drug (dragged?) a GT ragtop around on a trailer for years ...
But even then, getting a 3/4 ton or better truck to tow with is probably not a bad idea. As others have said; Ford, F250/F350 - 3/4 ton - 1 ton Dodge,...
Gene Beaird
bgbeaird@...
Oct 13, 2008 1:42 am
36413
I was rewiring the Mustang this weekend and was wondering if this is going to work. http://www.hotpursuit.net/HotPursuit/Driving/Projects/86MustangLX/ReWire / ...
Somebody else had mentioned using the trucks you already have.......you could upgrade to heavier springs or install air bags. Im sure doing this would be...
I see from this archive message that I can remove the cluster if I jumper the charging wire: http://autos.groups.yahoo.com/group/rrax-mustang/message/10620 The...
Jim, i'd get myself a trailer in a second if I had the room/storage space..I live by the beach in socal and alas, my home is essentially a not much more than a...
well if you were within an acceptable distance from me I would gladly loan you mine if I didnt need it at the time myself. It just sits around until a race or...
I use an autometer fuel level gauge with a bitchin' capacitive sender in my fuel safe cell. Still, it's the gauge that's made to read more or less the...
rust is not too big of a problem here in socal...strangely, even for me in the maritime zone, a couple of blocks back from the beach. anyway, santa barbara is...
THIS IS NOT ME  Dave Hester, DPh  SCCA, MCA, SVTOA www.rheacermotorsports.com ... From: David Hester <rheacerdave14@...> Subject: [rrax-mustang] Good...
Well when the tranny was pulled to fix the speedometer, it was discovered that the clutch and pressure plate are shot. This was a Ford Motorsport clutch which...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
