The site hasn't been updated in about 8 years or so... My brake set-up is a Floor-mount Tilton 72-680 pedal set inside the car. There is no plumbing at all in...
... I don't know about the SN95 GT, but the SN95 V6 MC that I have out in the garage mikes out at 26mm. Since the Fox is now Wilwoods and a balance bar, that...
Since we're on the subject .. Will the MC included in the old M-2300-C kit (described below from PPI's site) keep you from having to use one of the Max...
I have an 86. I didn't have to use any adapters but I used a LSC MC I believe. All my notes are 200 miles away.... but that has been 10+ years ago, and my...
I have an 88 Gt. I'm using Bilsteins and MM Road & Track springs. Settng my camber at home using the SmartCamber gauge. When I try to adjust negative camber I...
Doesn't surprise me with it being a Fox. I've owned several over the years and each was a bit querky when it came to alignments. My 86 open track car is easy...
wouldn't surprise me, but first make sure you're getting correct readings. are you measuring off the rims and not the tires? is the garage floor level? did...
Yeah, I'm measuring off of the wheel, just as the gauge is designed. I thinkI'm going to have to make sure the gauge is square again. I think it is a measuring...
Anyone ever slot the strut ears in order to gain (-) camber? ... measure again. ... gauge is designed. I ... think ... off on ... last ... install. ... cents ...
But you'll loose a little tire clearance. Not a problem, usually, unless you are cutting it close. Gene Beaird, 86 2R SVO, G Stock, Pearland, Texas ... From:...
Gene Beaird
bgbeaird@...
Jul 19, 2008 10:35 pm
36396
I'm going to look into this tomorrow and see what I can do. Hopefully, I can adjust it without having to enlarge the holes. Of course, I may have to do both, I...
I removed the dash from my 86. I'm looking to reinstall a simple AL one. I can't seem to find any pre-built dashes, so I was going to have one bent for me....
If you don't absolutely _have_ to have AL, you might try: www.florida50.com They have everything from fully wired panels with your selection of autometer...
Florida 50 brings the bling, but unnecessary for a race car. Hoerr Racing and a few other vendors sell pre-cut aluminum dash panels if that's what you're...
I "cheated" and put aluminum over my stock dash, and replaced all the gauges (but left the heater controls and vents). Then didnt like the shiny aluminum, so I...
Perception is a strange thing. I always regarded florida 50's approach as a "poor man's" approach. Not that their prices were so low or anything, but that...
... I thought about using these guys -- for about 30 seconds. Problems I have with these guys: 1 - The plate is 0.25" think -- WAY too think IMHO. 2 - They...
Scott, That's also one of the things I like about florida50. The ability to mount real gauges, in a clean cluster, in the stock dash, with a more-or-less...
here was what i considered a non-blingy florida50 panel: http://www.florida50.com/user/cimage/P1060879.JPG or, as a blank to put your own instruments in: ...
Hi Scott, I'm with you on the stock dash look and would have liked to have the opportunity to creatively gut the stock dash and keep the parts I wanted. But,...
I sent this to my other list, and meant to send it here, too. Thanks! ... From: Peter <pcrussell50@...> Sent: October 10, 2008 11:10 PM To: Fordnatics...
I have been towing my Mustang(3500 lbs) with my own car trailer (1200 lbs) with my 1994 half ton 5.8 E4OD 4x4 for years but if you look at U-cant-Haul they say...
Look at F-250 for Ford......D 200 for Dodge......C/K 20 for Chevy ... From: "pcrussell50@..." <pcrussell50@...> To: rrax-mustang@yahoogroups.com Sent:...
I almost never post on here but this is something I feel reasonably knowledgeable about. I have also drug (dragged?) a GT ragtop around on a trailer for years ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
