I'm fond of using a cardboard tube from a used-up roll of paper towels as a means to localize the noise. Yank the belt and "feel" the pulleys as you rotate...
I'd vote for trying the belt first. Spray or drip a bit of Armorall Protectant onto the belt while the car is idling. Just a few drops at a time or it will...
For Sale G-Force Street 5-Speed (T-5) transmission with synchro gear kit * Includes upgraded 9310 case hard high nickel steel alloy main shaft ((GFT5022-2-2PC)...
Rare appearance by age old lurker here. Since I have stuff apart anyway, I've decided to change out my old broken Isspro fuel pressure sender. I'm replacing w/...
I'm installing twin-turbos on my 1986 Mustang LX w/351W, but I no longer have room for a clutch cable. In the present location, the cable wants to come out of...
... Bob, We use a QuarterMaster setup <http://www.racingclutches.com/product.phtml? p=52&cat_key=89>on our car and I am very please with the results. The good...
Since this is a road race/autocross list, i've got to ask..are you planning on, well, road racing or auto crossing your twin turbo mustang? ... From: Bob...
Okay this isn't speed or handling related but I figured someone here would have a diagram or answer for me. I'm hooking up a reverse light camera that is...
Disconnect the switch at the tranny, check for power at the plug with a test light. Only one pin should be hot with the plug disconnected at the switch. The...
Thanks for the reply. Another fellow said the following: "For '92 the EVTM shows power to the switch from Fuse # 5 on a P/O wire. And out of the backup lamp...
So no one on here runs a fuel pressure gauge that's tapped into the fuel line at the schrader test port? I'm wondering what the spec is so I can make a line to...
from autometer FAQ "Do I need a sender for my electrical gauge? Electrical temperature and pressure gauges require the use of a sender matched for the type of...
I believe the thread is 1/8 NPT. I have a gauge on my fuel rail....its a Summit racing one.Cant remember the part number, but all the gauges I found on there...
... Steve, If you plan to run SS braided line over to your fender, maybe something like the following will help: eBay item #320265801008 Jeff Engel Happiness...
Bob, If you don't already know www.dariusrudis.com Look him up. He's the only OT driver I know who runs boost reliably. At least without a professional...
Thanks Jeff! That fitting looks EXACTLY like what I've been looking for! You wouldn't believe the ground I've covered trying to find fittings for that fuel...
I used to have an autometer gauge on the stock rail, and it did indeed come with the fitting to attach to the schrader valve. Hth. ... From: sealy37...
Ok, so been its a long time I've lurked and done DIY on my old 88 AZ Trooper Mustang. Time now calls for attention to some short-comings of the FOX3 platform....
mechanically, it'll work, but you might find it doesn't provide enough power assist. karl tried to keep his old booster when he swapped SN95 cobra brakes into...
I switched back from the Cobra booster to the old GT booster, and liked it better. I think the pedal feel is a personal prefence thing really... Now the...
+1 on the fox booster i use my stock '87gt booster, with a '93 cobra MC, and y2k cobraR calipers for _my_ pedal feel nirvana. i used to know this stuff like...
it also depends on what you're doing with the car. with high torque race pads, the pedal effort will be much better. but if you also drive the car on the...
the '87-'93 GT master cylinder is a fast fill design and won't work well with rear disc brakes. it's been a while, but if i remember right, the '93 cobra MC is...
A lot of people do use the 93 Cobra MC. I probably would have as well, but just happened to have the sn95 one laying around. Made my choice an easy one. -Vic ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
