I was wondering if anyone on the board has access to, or would be willing to share info, drawings, dimensions on torque arms, and panhard bar/rod set ups. I'm...
See the "Mustang Performance Handbook-II" by Mathis. It had decent schematics. I started with that idea, then looked at Griggs/MM, and created my own version....
Thanks Darius. ... From: "Rudis, Darius (D.)" <drudis@...> See the "Mustang Performance Handbook-II" by Mathis. It had decent schematics. I started with...
Thanks Robert. Darius' pics helped greatly as well. ... From: "Robert King" <gt40mkii@...> ... Actually, designing a torque arm and Panhard bar isn't too...
Hi Dan, If you or anybody else on the list is interested. I am planning to sell my old Griggs Heavy duty torque arm. It is just sitting in my garage taking up...
http://vb.foureyedpride.com/showthread.php?t=29556&highlight=torque-arm Another guy started this thread and I decided to continue it instead of cluttering up...
And now for something a little off topic. I posted this on the corral and corner carvers under general discussion but haven't gotten anything useful so I...
... might be helpful to put that picture someplace that doesn't require you to register in order to see it. i suspect you might be talking about double rod...
<http://www.tcmustangclub.org/events/2007/TCMC_Show_Flyer_2007.pdf> For those of you in southern CA, October 14th Mustang show in Ventura. I will be there,...
The Oct Buttonwillow event is on the same weekend. I checked the dates a little bit ago. Which is a bummer because I wanted to do both. I'll most likely go...
My garage is full of parts I do not need anymore. I am going to post these all on the usual boards, but I decided to give the lists first dibs. If you or...
My garage is full of parts I do not need anymore. I am going to post these all on the usual boards, but I decided to give the lists first dibs. If you or...
What he said :) Especially as relates to lack of room. I have the Griggs adjustable one, and the 22 gallon fuel safe cell, and a couple of studs come within a...
... Hmm -- if its closer than 1/2" or so, I'd think about trying to make some room somehow. things DO move around back there under hard cornering. Keep an eye...
Also, make sure to design for rigidity. The loads through the Panhard bar ("P" capitalized for Pete's benefit... :-)) are quite large, and deflection in the...
Sounds like you're parting out a nice car, and getting out of the mustang game entirely. I got an m3...but i still have my mustang. :) pete out... santa...
Actually my experience with the 5-link Mazda RX-2 and sprint car setups is that the roll center, if the bar is full width, is located at the mid-point of the...
Well, the definition of the roll center is pretty well defined is nearly any competent Vehicle Dynamics text. I'm not sure if you're trying to say that the RC...
Sort of. From what I said about the stock RX-2 you can gather that the Panhard rod has no effect on the RC because it terminates at the CL point at the rear of...
Hi Guys, On the outside chance that someone has seen this before I'm hoping that someone could help me with a small problem. A friend installed a Whipple...
George Kokolakis
rgbcons@...
Aug 26, 2007 4:16 am
35990
Hey All- I'm looking for info on completely rebuilding an 8.8 rear, end-to-end. Installing a new differential, gears, clutch packs, axle bearings, etc. Anyone...
I got the Ratech Complete (or Master?) kit from Summit for like $140. Also get the SOLID pinion bearing spacer from Ratech (like $6). Darius Rudis AOS Project...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
