just as i was posting. maybe i brought them down? i'll throw my question at you guys, too. is this hose orientation ok? i have a 90deg down elbow for the...
is this hose orientation ok? i have a 90deg down elbow for the top hose if you guys think i should use it. it seems better to use the elbow, but there's...
I would just make sure those hoses touch NOTHING but hold down clamps. If they are laying against anything, even temporarily, like under acceleration, turning...
Gene Beaird
bgbeaird@...
Oct 5, 2006 8:48 pm
35362
I would go with the elbow, it looks a lot neater. pcrussell50@... wrote: is this hose orientation ok? i have a 90deg down elbow for the top hose...
Forgive my failing memory, but aren't there supposed to be two throttle return springs on a 5.0 throttle? My throttle is very slow to return, and I seem to...
I want to say yes. I know that many sanctioning bodies require two return springs and the stock configuration counts. If my memory is correct, there is one...
Reminder from the Calendar of rrax-mustang http://groups.yahoo.com/group/rrax-mustang/cal SAAC-MCR Waterford Hills Roadcourse Sunday October 8, 2006 8:00 am -...
rrax-mustang@yahoogro...
Oct 8, 2006 11:48 am
35366
pete, it's better. you should use a 90 deg fitting on the lower hose, too. earl's recommends that for large hoses attached to horizontal ports, 90 degree...
ted, i don't have any adapters at the sandwich agapter end. the sandwich adapter itself is an-10. the only adapters i have in the whole system are at the...
Cross-posted... Just replaced my speedo cable: fox mustang, but with t56 and cruise. (Uses the same cable as fox mustang with t5 and cruise.) now, I get no...
Hello All, Went to an autocross yesterday where the end of the course was a series of nasty offsets that involved a lot of effort to steer back and forth to ...
Al, I don't know of one quicker than the 15:1 OE unit. A lot of the CP guys use steering quickeners from Coleman. I had one when I still had struts. With the...
Thanks for the reply. I am looking at the Coleman website at the steering quickeners and it is not obvious to me how they work. Do they attach to or replace...
When the cable melted on my car the gear IN the trans broke. Making so when I replaced the cable nothing happened. I had it fixed at the same time I got the...
well, that would certainly suck as* if i had to do that. in fact, i wouldn't do that until the next time the engne comes out. i might pull the vss after...
so... running up towards the 300k mile marker on my 5.0L and I pulled the plugs today to change 'em before a track event this weekend. They've been in there...
Fwiw, according to john griggs the "jumpy" needle is usually attributable to the springy inner cable catching and releasing as it turns. It's either a lube...
Your problem may not be rack ratio at all. Rather, with all the rapid wheel "sawing", you may be bleeding down the boost. Iow, you may be creating more...
One thing I forgot to mention is that I am running underdrive pulleys (alternator, water pump, crankshaft) which probably reduces the amount of boost available...
Saturday morning I took out my car, to pick up some parts, by the time I made it to the shop my clutch was almost impossible to use for first and second gears....
George Kokolakis
rgbcons@...
Oct 10, 2006 2:55 am
35379
Stretching cable, just getting ready to go? Al Hermans ... From: rrax-mustang@yahoogroups.com [mailto:rrax-mustang@yahoogroups.com] On Behalf Of George...
Is your cable breaking? Mine did the same thing when it broke. A couple of the wire strands snapped and I guess the others stretched throwing off the...
did you replace the stock clutch quadrant already? ... __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the...
I had the cable housing collapse at the trans end. The second time it failed I went with an aftermarket adjustable cable and it hasn't broken yet. -- Bob...
The jumpy needle can also be from a kink at the speedo end of the cable from mishandling the end while connecting it. The kink torques the inner shaft in the...
Anyone know what the fitting sizes are on a 93 Cobra master cylinder? Im told they are 'metric' but thats all I know at this point. danke ewk /15B//48E/ ...
pete, i rotated the 90 deg. fitting on the lower hose so it doesn't point straight down, and keeps the hose from sticking out at the bottom. the purpose of the...
Al, I don't have any direct experience with this, and it's not even a Mustang, but.. I'm active in the Subaru community, and there are a number of Subaru...
Sounds like the gear on the cable side has "apple cored". Its a pretty simple fix and its fairly common.....check the gear inside the tranny as well. Steven...
