I need a resource that has a complete list of the differences between the 01 Mustang GT and the Bullitt variant. I'm getting the SCCA to allow all 01-04 GT...
Kent, I happen to have purchased a 2001 GT shortly before the Bullitt was announced so I "collected" a lot of specs on the Bullitt to compare with my car. ...
Hi All, It's been a while since my last post, just started racing again at the FIR (Phoenix). On my last 2 runs of the weekend, I started spitting axle oil on...
Make sure to check the axle for wear Chris <steedpower@...> wrote: Hi All, It's been a while since my last post, just started racing again at the FIR...
You can rent or get free loaners on the tools. I'd do the bearings since you are in there any ways. also check to ensure the axle breather is clear. and a...
Hi guys- I've been putting this off for a bit but need to replace my speedo cable on my '90. I had checked the trans end and found the cable/driven gear had...
Chris: If you're going to replace the seals, replace the bearing as well. To replace the old bearings, you could use a puller. I used an long piece of...
You should be able to reach up under the dash and disconnect the speedo cable from the speedo without disassembling anything. Is that the question? If you've...
You should be able to reach up under the dash and disconnect the speedo cable from the speedo without disassembling anything. Is that the question? If you've...
I'll make this semi-short and sweet :-) Saturday's 1st session I run w/800# springs. I go slow, 3/4 of what I think I can do. Just take it easy the first...
I'll make this semi-short and sweet :-) Saturday's 1st session I run w/800# springs. I go slow, 3/4 of what I think I can do. Just take it easy the first...
Does anyone have a compilation of the available Fox Body front bar sizes, aftermarket and stock? I thought I had a page saved that listed them all, but I can't...
I've got one somewhere, but I just got back from Laguna Seca, and I need to do a weeks worth of work in the next two days and then leave for Phoenix in two...
... Sounds like the sort of info I'd have saved, too. I was only able to find this in my archives. http://www.miracerros.com/mustang/sway2.htm HTH, Jeff Engel...
Hello everyone, Its been a very long time since I posted a message to this board but I need a bit of help. I just pulled "Whoomah" out of the barn after a ...
Hey Guys, Since I've been on this board for a while now and have gotten to speak with a lot of you I thought I'd share this with Ya'll in case you ever...
R> Does anyone have a compilation of the available Fox Body front bar R> sizes, aftermarket and stock? I thought I had a page saved that listed R> them all,...
... Hey Bob, Please understand, I'm in no way a "turbo expert" but I did surround myself with some to build this project so I'll tell you what I know..... :) I...
Personally, I think the duration is a bit conservative with 217/222. I would go for at least something like 224/236. Also the L/C is narrow at 114, and...
... man, haven't heard that term in awhile. It absolutely floors me you can stick a turbo out back of the car and get a decent system. Heard a lot of good...
... Guess I did end up picking up a phrase or two from dear old Dad..... LOL ... From what I understand, the technology has been around for a while. I remember...
Teddy, Sorry about the delay in responding. In answer to your question I have a relatively stock 2003 GT. Thanks for the heads up on keeping the stock master ...
Hi all, It's starting to get hot here in Texas, and my A/C is on the blink. Some of the parts I want to replace with OEM parts, but I'd rather not pay the...
Just a curious question. Has anyone heard about anyone setting up an 05/06 Mustang for E Street Prepared? I'm wondering just how good that chassis is, and how...
I bought my A/C parts from www.fordpartsnetwork.com and was happy with both the service, shipping, and prices. I had trouble with that link a little while ago,...
I've bought several things from them too, and been happy with the service. The reason the link didn't work is that Ford recently made them change names...it's...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
