Enough to turn it over. 175 amps, 130 CCA. Crap, my alternator only puts out 30AMPs...most tractors probably take more power than my 76 Capri. Once it's...
Are you using a reduction gear starter? ... __________________________________ Do you Yahoo!? The all-new My Yahoo! - What will yours do? http://my.yahoo.com...
Stock starter. It's a 1976 Capri with the stock 2.8 litre V6...soon to be 400 V8 powered. On Wed, 1 Dec 2004 20:02:40 -0800 (PST), Richard Lopez ... -- I'm...
... No doubt. They do have a slightly better L&G battery for $5 more, 275A, 230CCA. I am using the 175A, 130CCA battery. When I eventually swap in the 400...
(4) 17x9 4 lug cobra R wheels with (2) hoosier A3S03 /(2) kuhmo victoracers . paid 600. for wheels/ $800. for tires . located in south florida call mike...
I finally got to play with the car today. My wobble, which is on an airbagged car without tilt seems to be coming from a bushing? From what I can see, is...
like i said, easier to raid the junkyard and swap the steering column. -teddy ... __________________________________ Do you Yahoo!? Yahoo! Mail - Find what you...
I may do that, but doing that the newest part I would be able to use would still be 11 years old. If possible, I would like to replace the bushing (if that is...
That should work. In A/sedan, I use a regular size for ballast behind passenger seat area. ... No doubt. They do have a slightly better L&G battery for $5...
... if you figure out what to replace it with, that would be useful information for the list. i didn't put much time into it before deciding that swapping the...
I was wondering if somebody could give me some alignment specs. The car is an 89 hatch with an Eihbach prokit, M-2300 brakes, 17x8 wheels w/245 45 17 tires,...
Unless it's inconvenient, I'd probably go down to the dealer parts dept and take a look at the diagrams in the parts system then find out what assemblies are...
The time has come and I must sell my car ASAP. I will accept the best reasonable offer or may try E-Bay if there is no local interest (MA/NH). Let's make a...
Ruck, Jeffrey
Jeffrey.Ruck@...
Dec 5, 2004 11:41 pm
32760
sent to two groups...longish ok, so i have these two sets of oem hydraulic roller lifters that i've been keeping around for an engine rebuild. that time has...
for the price of a new set of lifters, get a new set........ ... Thanks David Fincik 89 Mustang LX, A4 331 Stroker, 325rwhp. 360rwtq, Full Griggs, Cobra brakes...
Where are you located and how much do you want for the car? Mike Ruck, Jeffrey wrote on 12/5/2004, 3:41 PM: The time has come and I must sell my car ASAP. I...
Mike Mak
MMakintrax@...
Dec 6, 2004 5:26 am
32763
BUY A NEW SET OF LIFTERS @ around $130 for set its cheap insurance! cheaper than building another motor. peter c russell <pcrussell50@...> wrote:sent to...
For the amount of time and effort involved with disassembling a set of lifters, cleaning them, re-assembling them, and still not being able to know for sure...
John Nelson
cybpunk@...
Dec 6, 2004 7:50 am
32765
I've got some Tilton race style M/C's mounted down at floor level on the engine side of the firewall. Currently the reservoirs are remote mounted in the...
how do i drain a filled lifter so that the plunger will move up and down against it's spring? 'asta pedro santa barbara, ca No virus found in this outgoing...
Shortly after building my engine, I saw Crane sells roller lifters for about half of what the FRPP lifters were going for at the time. I would have to agree...
I was able to get a printout of the factory spec sheet from the dealer for caster/camber/toe. It has the tolerance range & recommended settings. I think that...
... The ... wheels ... aligned ... Thanks in ... This has been gone over dozens of times in the past. A good starting point for almost any Fox or SN95 Mustang...
I am moving my race style master cylinders. The kits come with short sections of rubber hose of unknown composition for connecting remote reservoirs to the...
Anyone use(d) the ACCEL DFI GEN VI system? Looking for feedback and instructions for setup. I have the CALMAP V6.32 software but, need to build the PC...
I was pretty sure that the guy who did the last alignment deviated a bit from factory specs, and if memory serves me correct the springs came with some...
