So we're Removing Sound Deadening Material from our Mustang. After trying the Dry ice method to no avail we used a heat gun to get the Tar-mat out. Now, how do...
I think you're right-on with the dry ice. You just used it too soon. One of my friends used dry ice and a dead-blow hammer to remove the glue on his car after...
I found that pulling this stuff off during the winter is much easier, so I'm not sure why the dry ice didn't work. In the winter, I just hit the top tar stuff...
to me, it sounds like he already got the tar off and is now trying to get the residue off - perhaps for painting. tar and bug remover works well for that...
Yeah, that's pretty much what I'm doing. Heating it with a heat gun, scraping off what I can then using the chemicals to remove the left overs and the ...
Our method is a little extreme - but it works great. :-) Strip the entire car down to bare metal frame. (Install the cage, SFCs, and all welded metal...
Whitehead, Scott (S.)
swhiteh3@...
Oct 4, 2004 12:12 am
32381
Scott, I missed this program.. do you know when it will be back on again OR does anyone have a copy of it? Mike Mak 88 Saleen Full Griggs Whitehead, Scott (S.)...
Mike Mak
MMakintrax@...
Oct 4, 2004 7:52 am
32382
Mine was done in the winter "room temp" (so it was about 50'F). I went at it with putty knife. Then, I used the air hammer with a chisel tip for other parts....
Rudis, Darius (D.)
drudis@...
Oct 4, 2004 12:07 pm
32383
My heater core finally got replaced. I have to say though that the FORD engineers that designed this setup need some re-education and should spend time working...
George Kokolakis
rgbcons@...
Oct 4, 2004 1:17 pm
32384
I'm in the middle of an evaporator/heater core replacement and coudln't agree with you more... -- Nelson 1990 Mustang LX 5.0 http://fiveoh.homestead.com ... My...
Sounds like the front driveshafts that BAR had for one race this year.... :-) People often speak of innovation in F1, but in most cases, any real innovation...
Whitehead, Scott (S.)
swhiteh3@...
Oct 4, 2004 7:12 pm
32386
Geez and here I am gluing in sound deadener material. I bet I have over 100 lbs of dynamat and lead lined foam sound barrier pads in this car. Turns out...
... I recall the tarmat/fiber insulation stuff removed from the car weighing in at 18lbs. Is the extra weight in your setup because of the muffler inside the...
Why do you need to add so much Dynamat? Are you installing a mega wattage stereo? George. ... From: Peterson, Preston [mailto:preston.peterson@...] Sent:...
George Kokolakis
rgbcons@...
Oct 5, 2004 4:00 am
32389
weight equals slow....... our cars are already tanks....... if you want speed you need to get rid of the fat........
I'm changing cams. The timing gear is stuck. The cam gear doesn't want to separate from the cam, and the crankshaft gear seems really jammed on. This is a Ford...
... It's fairly common. When disassembling cores I use a pair of crowbars, but in that situation I don't care if the gear is destroyed. If some judicious...
Dave Williams
ronin@...
Oct 5, 2004 3:12 pm
32394
Preston, Use a propane torch to heat up the gear around the camshaft. The hole will enlarge enough to get it off without tearing up the gear. I use this method...
I have a set (4) of 16 x 12" 3 piece Real Racing wheels, 5 lug 4 1/2" circle for a mustang. Will work with 13" brakes. Very good condition. I can take some...
Charles Penney
c.penney@...
Oct 5, 2004 5:19 pm
32396
FYI, I used the Ronal R9 wheels 16x8 on my Zephyr Z-7. http://www.dariusrudis.com/mustang/zephyr/ Ronal: http://www.ronalusa.com/wheels/r9.html Darius Rudis -...
Rudis, Darius (D.)
drudis@...
Oct 5, 2004 5:29 pm
32397
this last spring, i blew my second engine at a track event in the last 6 years...at the nasa event at cal speedway. fortunately for me, the destruction didn't...
I've always gotten towed outta the sand traps by the rollbar (with the rear hatch open). DOH! ;) http://www.dariusrudis.com/fme/scmc/scmc_2002gingerman_07.jpg...
Rudis, Darius (D.)
drudis@...
Oct 5, 2004 7:12 pm
32399
I use an old piece of seatbelt webbing. Mounted like a regular belt to trunk and then again to rear bumper. Leaves a tag out the back. For the front I have a...
DO NOT pull by the radiator support frame! Its not sturdy enough, and you'll tear up that piece, not to mention the radiator along with it. Darius Rudis - QTM:...
Rudis, Darius (D.)
drudis@...
Oct 5, 2004 7:30 pm
32401
I will second that. My father's '79 (back in 79 or 80) was severly damaged by a towing place that towed his car 20 feet from the bottom of the radiator...
On Tue, 5 Oct 2004 15:12:13 -0400, Rudis, Darius (D.) <drudis@...> ... I have a tow loop on my front bumper, right in line with one of the longitudinal...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
