Pat is that seafoam as in the stuff you find at the beach? Simon ... From: "Patrick Crum" <pcrum@...> To: <royalenfield@yahoogroups.com> Sent: Tuesday,...
Following the various advice given by this group I went ahead and ordered a KN Air Filter, fitted it on saturday along with a new 117.5 main jet (as...
I've never used it, but I hear it's good. Some guys over on Bulletech mentioned using it about a year ago with positive results. Pat ... From: "Simon Schuh"...
I was wondering if anyone had tried velocity stacks on their bullet with a Micarb and what the result was. there are some on ebay with a fine mesh over the...
About month ago I did the same thing - installed conical air filter and removed that dummy box. Changed also main jet and raised the needle. I'm sure that my...
The Description of the Barrier Between Two Seas Scientific investigation: Oceanographers, in the wake of the scientific progress in this age, have discovered...
The Description of the Barrier Between Two Seas Scientific investigation: Oceanographers, in the wake of the scientific progress in this age, have discovered...
Clark's Corvair, who remanufacture MOST parts for Corvairs, www.corvair.com make a water injection kit. I installed one on one of the hot rods a few years...
... what the result was. there are some on ebay with a fine mesh over the bellmouth and ... Hi Simon I had been thinking about it for some time, as i had road...
Pat, You've burst my bubble!! we're moving to the coast in a few weeks and there I was thinking I'll be able to de-coke my bike with the lashings of 'sea foam'...
Well just go ahead and ride the bullet straight into the surf until it gets so deep that it dies and you have to drag it back up onto the beach! By the time...
I have been concidering this for a while. If the K&N conical filter makes a loud sucking noise would the bell mouth do the same? I am leaning towards the...
... running the engine at > enough rev's that it isn't going to stall out and lightly spraying some > water from an atomizer bottle into the carb intake ...
I've been offered a 2001 Bullet 500 ES... I've had a 99 model kick start for a while and would like to have the electric start... Any known problems with that...
Royal Enfield Mailing List - a note from the moderator "Guidelines for Use"... sent automatically on joining, and each month thereafter. Updated occasionally. ...
royalenfield@yahoogro...
Jun 1, 2004 11:32 pm
32651
... only ... Heiti- that hose could be changed for a much sturdier piece of reinforced radiator hose. If you have an Auto Zone around ask them for a part#...
The only difference between a 2001 es and a 2001 K/S only is the primary cover, starter and the associated clutch for the starter. Mechanically the engines,...
This will sound distinctly odd to enthusiasts here, but its been a cold spring, and lots of rainy weather whenever I might have taken care of these things, and...
True a big plastic water tank would look ridiculous on the bike. I was thinking of a stand setup for pats Decoking idea, as a garage based tool. Simon...
I was approached by the local Pioneer Museum and asked if I wanted to put my bike on display there instead of riding it around on the streets getting it ruined...
Good on you Dave, Welcome back. Pat ... From: David Hill [mailto:davhill@...] Sent: Tuesday, June 01, 2004 6:21 PM To: royalenfield@yahoogroups.com ...
... When I went to the 'Berliner Oldtimertage' - an oldtimer show here in Berlin - to look at nice old cars and bikes some weeks ago, the guy at the entrance...
Is it OK to make the new "hose" shorter than the old rubber manifold, bringing the carb closer to the cylinder? The throttle cable on my bike rubs against the...
... To use radiator hose, you must have the alloy intake manifold. The carb and the manifold have a groove, the rubber connector from the factory has a ring in...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
