Royal Enfield Mailing List - a note from the moderator "Guidelines for Use"... sent automatically on joining, and each month thereafter This list was created...
royalenfield@yahoogro...
Mar 1, 2003 12:12 pm
21650
when chainging the oil , with the filter out some oil drains where the filter was. my question is , is it possible when that oil drain out from where the...
I think you should soak the filter in new oil for at least ten minutes before replacimg the cover and you could also prime the timing side by rmoving the...
My guess is that very few people read this, "seen it before". Judging by recent messages, a few people need to refresh their memories of the following...
Any other alternatives to lubrication other than veedol oo grease? Like gl-5 hypoid 85-140.How many ounces of this type oil would the trans require?Any long...
... 85-140 will work just fine. You can use just about any gear oil or grease, some will just run out a little faster than others. Amount? I don't know, just...
Hi all I have noticed lately that the kick start lever on my 2002 Bullet 500 is doing odd things. When I start off in first, sometimes the lever moves back...
I have a Madras Bullet , 3 years old butr when I bought it a month ago it only had 90 miles on the clock. The previous owner had given himself a hernia lifting...
Andy, Last summer I too noticed my swing arm moving in the wrong plane and found the swing arm bushings had loosened. A low amount of torque tightens them, but...
Andy, These are bonded rubber - the old "metalastic" bushes. Normally they last for a lifetime! They are pressed into the swing arm and can be a pain to move...
THE TESTER The 'BOSTING' newsletter of THE BIRMINGHAM TESTERS RUN SPRING EDITION From Alaska to Japan but mainly Deritend to Sedgeley. Editor,non-intellectual...
I forgot to thank you for the Buzz circular It seems now that Bergerac will stop and that Ryanair will continue with a service via Bordeaux I am taking Olivia...
keith parker
castang@...
Mar 3, 2003 2:06 pm
21663
You can actually in a pinch put just about anything you like in the gearbox. As long as it is slippery. The 00 grease and oil mix is "pre-installed" by REM...
hey tracy On the rare occasion that I need to harness the blinding speed of my bullet, I get a hard crack on the back of my boot from the kickstarter. I always...
Hello all, This may not be the uber-correct forum for my question, but I was wondering if anyone owns an Enfield in California? I am moving there this June ...
My Bullet is sort of the test bed for "what if all you did was add gas, change the oil, and ride it?" I'm no mechanic, but I've ordered Pete Snidal's CD and...
In a recent message Andy, you gleefully stated that in 2006???? Bullet engines would be declared pollution machines and there would be plenty of spare on the...
Just look up the new legislation that awaits all road users as the emission laws are going to get very stringent. If Madras is launching and already testing (...
Hiya, Dont know what my neighbors to the south are going to dictate to us next. Maybe you can find something at this website. So far, So good here in Oregon...
Dear Tracy(scratching his head at this point) No doubt Jan and Pete will tell you all about your problem but IMH(and highly limited)O, it's probably an ageing...
It's probably caused by the layshaft binding in the bush inside the kickstart shaft which supports the right hand end. It's a quite common problem on Commandos...
Andy! A little note on this from the homeland of the Bullets; The usual mistake most people do when the try to find a reason for things is to put everything...
Am I correct in assuming that the inside face of the oil pump spigot (wider, threaded part) should NOT push against the cork seal on the crankshaft end. In...
Hello Bulleteers, I am 6'3" and suffer from back pain, specially after riding my 1994 bullet around, so I have tried various mods to smooth the ride a bit ...
Jan Lang wrote "A little note from the homeland of the Bullets;" snip <<In India, the MAJOR market for REM, the all-overshadowing concern and utmost only valid...
As you can probably guess, we've been around and around with this one.
I think it's fair to say that the consensus is that you want to run
the thinnest oil...
... <tomgdaly@...> wrote: In yet other words, the seal should ... Tom, I haven't worked on the pump. Maybe this link will help, the pump detail isn't...
Hello, Sadly I must sell my Bike... http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll? ViewItem&item=2405566251 I also have these new alloy rims for sale. ...
