Ron, are you still on this board? I haven't seen you post for a while. Reply here or to mx340joe@... I have some questions for you about my 340. Joe...
Hello, I've been wanting to get in touch with Gary Edmond. He was a Rokon factory rider in the 1970's and rode a Rokon for a Gold Medal at the 1976 ISDT. I'd...
... Last time I was out with Gary and his wife for dinner he was still living in Lisbon, CT. His home phone number was: (860) 822-1342 I you get a hold of him...
Yup Marc has the right info...I bump into Gary every now and then at the local diner... Dave V. shiftless in CT ... From: rokon94 <mdodge@...> Subject:...
Thanks Dave and Marc. Dave, I sent you a couple of e-mails regarding the brake rotor but in case you haven't gotten them for some reason, Yes, I'd like to have...
What's the secret to dissassembling the Betor forks on my 1976 RT-II? Following the instructions in the RT340 owners manual, I drained the oil and removed the...
... drained ... Mine ... the ... they ... Hello Bill loosen the fork boots and lift them up at the top of the forks there shold be a snap ring or a wire ring...
Hello everybody is there a rokon riders club out there some where, i have never seen one if there is. And if not would anybody be interested in joining one if...
Bill there should be a "socket head cap screw" (allen screw) on the bottom of the fork where the axle goes through...these can be a pain,,,best to use an...
Thanks Dave and Carl. I did have the socket head cap screws removed the first time I tried to get the fork bottles off, but at that time, the forks were still...
I used BelRay 30w fork oil in mine. Worked well. Also, two seals in each slider is common. You can buy new seals (35mm) for Betors thru DennisKirk and ...
Way back in the 70's, we used to use ATF 'cause it had better antifoaming and flow characteristics. We replaced the seals with ones from Honda- they NEVER...
I have one of those 'no spring' Betor forks... pretty soggy! Time for springs. I think I would have to pump 40 lbs to make it work, the front end rides...
I have Rokon MX340 serial # 133 that I am considering selling due to a bad right shoulder I have injured 3 times. I bought this new from Dave Mungenast's Dirt...
On May 23rd 2009 there will be a trail ride for vintage enduro and mx bikes at Dave Flachs farm in Coeymans Hollow , New York which is about 25 miles south of...
On May 23rd 2009 there will be a trail ride open to all 2 stroke , drum brake , dual shock , air cooled bikes ALL MAKE are welcome. Following the day of riding...
On May 23rd 2009 at 9:30am there will be a Vintage Trail Ride hosted at Dave Flachs Farm. All 2 stroke and 4 stroke , air cooled , twin shock ,drum brake bikes...
On May 23rd 2009 there will be a trail ride open to all 2 stroke , drum brake , dual shock , air cooled bikes ALL MAKE are welcome. Following the day of riding...
This past week we cleared the trails in preparation for the Vintage Trail ride. On May 23rd starting at 9:30 to 10:00am we will gather at Dave Flachs farm....
3 days to go, for the 2009 Vintage Trail Ride May 23rd Ride them do not hide them . Join us this Saturday May 23rd at Dave Flachs Farm Following the ride there...
Tomorrow that's right tomorrow is the Dave Flach Vintage ride. So if you have a vintage dirt bike and want to have fun and want to use that bike tomorrow the...
Does anyone know the size of the O rings for the fuel shutoff? Thanks, Joe _________________________________________________________________ Lauren found her...
Joe, The part # is 03-113 and is a VITON. You can get it at APPLIED INDUSTRIAL TECHNOLOGIES,look them up on the web.This part number is a OEM part for the...
Hello, I am hoping to have my 1976 RT-II back together in the next few weeks, to the point where I will be staring it up again for the first time (IN ALMOST 30...
Bill, I will give you MY way that has always worked for me ( 34 years with Rokons ). I mix one 12oz Golden Spectro to 5 gallons of 93 or 94 octane. Run bike...
Thanks Mike, That seems like a good plan. Bill To: rokon@yahoogroups.com From: RT340AUTO@... Date: Tue, 16 Jun 2009 19:54:21 -0400 Subject: Re: [rokon]...
I would also recommend using a Teflon or graphite coated piston when possible, and after break in pull the head and piston and look for high spots on the...
I'm new to the group with a 76' RT II. Would like to know if there are any other owners in the KC region or 150-200 miles radius. I'd like to be able to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
