Link posted in link section. It was with a heavy heart that i had to watch the 9th annual reunion ride pass me by as the hurricanes came and devestated the...
This was posted earlier tonight on the Vinduro board ... If any one is interested I will forward Jons address to you .. Thks BT The Rokon bits include two std...
I am trying to find information re a rebuild kit for 3 position adjustable Betor Shocks #102686 for my 1975 RT 340. I also would like to know if a rebuild kit...
Bruce cant tell you about the Betors rear shocks but maybe Hughes Bultaco might be able to help you .... if you want fork seals for the fronts they are listed...
Thanks a lot, I will check out your suggestions. I will let you know how it turns out. thanks again, Bruce ... From: cdnbrg To: rokon@yahoogroups.com Sent:...
Did a search of archives and didnt find anything My question is were the rotors off anything that we know of ..... is it a Kelsey Rotor did Harley use them or...
BT, How many donuts did you have at ISDT 03? Were you in a sugar induced haze, when Mark Hamilton told us they were industrial saw blades cut down......Now...
David you crack me up ...I was obviously in a Donut fog ... with the New England weather you treated us to and all the coffee and donuts I must have been...
Its time for me to be moving on. I had a RT340 for the first go-round in the mid 70s, then got the bug again (mid-life crisis?) in '01. Now I found that I've...
It looks like the URL did not copy over correctly from my previous message for '72. This should be better http://www.albany.edu/~gr743/1972%20Rokon.htm Thanks ...
I just picked up a set of Snowflake wheels but they are just the bare castings.I plan to get them powder coated to use them for flat track.I just picked up...
Yoy CAN NOT powder coat the Mag wheels, the gases will leach out when the wheels are heated and ruin the job....just use a good epoxy paint this IS the voice...
Don Jones (fellow list member) or Central Snowmobile in Green Bay, Wisc. Dave V shiftless in CT "John Donnell,Sr." <PUDLY007@...> wrote: Does anyone...
For all you guys looking for instrumemt panel stuff, check out this guy on eBay http://motors.search.ebay.com/_W0QQsassZ3976monica He's got a route chart...
Hey guys, things are very quiet! I still need to know what plug I should use- long/short reach?, heat range?, brand? I took it riding at a VMX event but only...
Peter, Parts manual lists an L3G Champion, I use a NGK B9HS. All engine bolts are metric! Exhaust flange is 8mm nut on 8mmm stud with 8mmm wave washers. The...
Thanks Dave, my plug guess was in the ballpark. The nuts I lost were from the rubber mounts, but I have spares in my shed, just not at the race.I havent done a...
Guys: I'm back from Iraq on two weeks leave and fired up my RTII within 24 hours of getting home. I had my engine rebuilt (top/bottom ends and ignition) by...
Ernie, I am wondering if they did pressure test on the crank cases? You may have a air leak and it will do funny things too. Does your bike have a bleeder...
Ernie, If it ran fine before Iraq I would think it was the result of sitting and minor corrision in the advance mechanism. You \'ll have to pull the flywheel...
Brian: Thank you for the kind words and your thoughts on the engine. All carb settings are stock. Main jet 310, needle jet Q-5, needle 6FJ6, pilot 35, air ...
Brian, No, it does not have a high idle. By the way, I just came up from the garage where I just checked the timing...it is spot on. Right about 3mm BTDC. ...
Ernie, I cant remember if the gasket is copper? If so you can re-use it. you need to anneal the copper. just set the oven to 500 deg and put it in the oven...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
