All, Happy New Year! I am almost completely done with my Rokon restoration but am looking for a headlight. It's one of the last things that I need to finish...
Hi everyone, Happy New Year, new to Rokons and this site, I decided to pull an old Rokon out that we had in storage to run at the AHRMA Bike Week National in...
Hi everyone, Happy New Year, new to Rokons and this site, I decided to pull an old Rokon out that we had in storage to run at the AHRMA Bike Week National in...
Hello Jack and welcome to the group ... look forward to you posting some pics ..... engine parts can be bought from Central Snowmobile ..... try to get us...
... Thanks for the warm welcome Brian, no numbers on the frame or motor, just received the frame back from the sandblaster and could not find any markings.......
Hello Jack, ... Wow, that sound pretty ambitious. Good Luck! ... Sounds a lot like a GMR to me. Pictures would help alot. The cast wheel/spoked wheel sound...
... the front and mounted new rubber, blasted and painted frame, lined tank to cure leaks, forks cleaned and new seals installed and NOS Petty plastic...
Jack, Dennis Kirk has pistons for several old snowmobiles in stock. Somewhere in an old post, there is a note on which snowmobiles engines are the same. I...
Looks like I will be needing a seat for my bike, RTII style, is there anyone out there with one they would part with, any condition is fine. Thanks, Jack...
Hi guys, uploaded some photos of the bike I am putting togeather. Questions: Is it a GMR?? What are the four holes for between the motor mounts hole and the ...
Please look under "Jacks Rokon" photo album, I figured out how to set the album up. Another detail of note. The left side pipe mount has been cut off and ...
Welcome to the group. Oversized pistons are very hard to got. It is best to have the cylinder sleeved back to standard. You can get standard pistons....
... Yes and No. The frame is a GMR. The swing arm looks like it's probably off of a 75 MX. The front mounts are the stock MX mounts. The rear mounts were...
... The GMR pipe was routed in the tunnel under the engine and reduction box and exited on the left side with protectors on each side of the tunnel. When the...
... mounts and gussets are not factory, diff gauge metal, poor quality welds, hand fabricated. Is it possible to get an axle to pivot measurement? Where can I...
Can any one suggest a 19 inch front knobby that works, i have tried an nos metzeler with out much luck. The rubber is to hard, thats what happens to a 35 year...
there are several modern 19" tires you can run now. it depends on what type of riding you will be doing? any ideas? BrianB [Non-text portions of this message...
Nope, that's an RT seat not an RT II! Dave V. shiftless in CT jimptg <JimPTG@...> wrote: Hi Jack, This may be your lucky day, there is a seat on ebay -...
To the Group I received the following email on other Yahoo group I am a member of. If you belong to ANY Yahoo! Groups (you do as you are reading this) - be...
Hi everyone, what are my options regarding replacement rear disc brake pads. I have the rectangular bent ear K&H type. I looked back into past discussions...
You can order some from Summit Racing. The part # is WIL-150-1251K cost is 22.95 for 4 pads. They are even countersunk for the hold down screw. Bill Davis...
Bill, That's for the round puck type, the rectangular bent plate type is almost impossible to find and relining is usually easier on this version. It was a...
Bill have you tried them ??? if so I will add the part to the data base .. thks BT ... From: rokon@yahoogroups.com [mailto:rokon@yahoogroups.com]On Behalf Of ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
