It's been so quiet on the group, I figure everyone must be busy restoring their ROKONs this winter. How's everybodies project going? Mine are progressing well...
Well my winter projects have been a 76 125 Husky basket case that I made into ISDT mode almost done and a 1975 250 Husky to be done in ISDT mode also ... My...
Brian, Howard Watts out in NM had some hubs all cleaned and ready to go...He offered me a choice of complete wheel or cleaned and prepped parts. I don't have...
... transmission final drives and tracks back on my JD bulldozer :O) I'd rather be working on bikes,,,,the parts dont weigh nearly as much! hehe I've been...
... You've had a better and more productive winter than I did Dave. After I got my '76 running I may have had a roller bearing go bad -- the engine still has...
Greg, Central Snowmobile(.com) can rebuild your crank if the bearings went. Actually any good machine shop could also, but I would trust someone who does two...
Check the free play up and down...don't worry to much about side to side ... From: daview01 [mailto:dvieaux@...] Sent: Thursday, March 17, 2005 11:11 AM ...
... Don, Free play up and down is very noticeable :-( (especially when compared to my second motor -- the one with the stuck-on flyhweel ---which has no...
and colour coded................BT unlike BT who has his all inventoried, marked and sorted in their respective "Tim Horton's Donut Boxes". I'll bet BT even...
Dave's remodeling his basement; he's rearranging piles of donut boxes. Are you still rebuilding that engine on your kitchen table? BTW Dave: My youngest son,...
For you New Englanders, I'm thinking of trying to get a "ROKONfest" together. At present it would just be a day of BBQ, and Bench Racing, possibly in June....
Good Idea Dave .. I hope that there is interest in this .....good luck BT ... From: rokon@yahoogroups.com [mailto:rokon@yahoogroups.com]On Behalf Of daview01 ...
I'd be interested in attending with my "Garage Queen". ... _______________________________ Marc Dodge Transmissions Services Supervisor Connecticut Public...
Hi Dave, sounds good. I'll offer my house as a site, if that's any help. I have plenty of land and riding area. I don't know how centrally located I am for...
Finally ready to begin driving my 74 ST340 on the streets, but it seems to be jetted a tad rich. It was set up for ice racing by the previous owner, which I...
Sorry, I haven't tried any new belts yet...I still have a couple of original spares I got from Jim Hoskings, he may have more. If you have an old one, take it...
Sorry I cant help you on the original jetting either ..... I have played a lot with the original and with all the racing it changed from location to location...
The manual says: Main Jet................310 Needle Jet..............Q-5 Jet Needle..............6FL6 Pilot Jet...............#35 Air screw (turns out)...1 1/2...
Well, I checked and I am using the Gates 6312 belt. It seems to working just fine. I think the 6312 is a little bit wider and a little bit shorter than the...
Finally received Gates 6312 belts from Rockauto.com at $23.89 each for my RT340S. Wow, what a difference a belt makes! Though many have said it can make the...
I've had mine registered and insured for over 10 years in 2 states. Not only does it turn heads, even the ladies ask me what it is.... (The rotary factory...
Guys, I'm new to the group and am looking to buy a RTII340 for restoration and riding around with the kids. Have been fascinated by Rokons since I first...
Ernie. I have a very nice RTII. I want $1200. you can call me tomorrow at 317-846-1005. brian borshoff [Non-text portions of this message have been removed]...
I will get some pics next week. list of items done:new or rebuilt 1) rebuilt engine,new piston and all new bearings and seals 2) comet primary clutch and gates...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
