Was out riding the RT2 when the rear brake caliper started dragging. Well needless to say large rectangular pad took some considerable wear. The last time I...
Eric did you check the Arccchives search for this topic ... it might have been answered a while ago .... I think Dave ( ebay ) Vieaux might have done something...
Eric, It's my understanding it was a standard Kelsey-Hayes pad with the ears stamped back. I tried and could not duplicate a good working copy. Not to...
Hey Dave, What else can you tell me about the best round pucks being from a Caterpillar bulldozer? Any specific info? I assume that you or someone on this...
Bob if you get any info on the Caterpillar numbers pls post it and I will update the Commercial parts list ... also post the Yankee numbers and I will put...
YankeeBob Wilwood also has pucks, but not the ceramic ones. Wilwood also makes a caliper which is a direct bolt on replacement for the 500. I have used 2 on ...
Hey Brian, will do some night this week. Bob ... From: Brian Taylor To: rokon@yahoogroups.com Sent: Monday, July 05, 2004 10:52 AM Subject: RE: [rokon] Re:...
Bob, The only information we got from the engineer was "a steering brake puck from a caterpillar". would assume something common and pre 1976.... Here's the...
Hi you guys: I suggest that you contact Mark Hamilton, care of the ROKON factory. He should be able to answer some of your questions. Wish I could remember...
orla larsen
orla-l@...
Jul 7, 2004 12:45 am
3043
Thanks Orla! Mark was at the ISDTRR "04 with us. He's the one that told us the info about the catapillar pucks. We had a great time at Dalton. Some of the ...
Thanks Dave. When I was talking to Tom at the factory a month or so ago, he mentioned that Mark was still doing consulting work for ROKON. You just can't keep...
orla larsen
orla-l@...
Jul 7, 2004 1:28 am
3045
Got my first Rokon but can't start it. I know it runs, several other people have started it and I have ridden it, but I can't get it to start. I think I am...
Ted, I may be mistaken but I think the drilling was only on the early RT's. My later engiunes were already drilled. If everything is properly set and you got...
Ted try to pull the starter cord slowly until it is on the compression stroke ( when it seems to get harder to pull ) then allow the cord to recoil...... then...
Ted, are you sure the bike isn't flooded? On mine there is a valve at the bottom you can open to empty the crankcase. Brian B [Non-text portions of this...
Hello Everybody, Well, I finally got some time to give you all report on Vintage Motorcycle Days. I saw a couple Rokon List members, Brian Taylor was down...
Hello Ted, ... Brian and Dave have give some good advice, get it up on compression and give it a good quick pull. You might want to check the timing and the ...
Ron, Have you listed what parts you used for your ignition mods? Wonder if Jim Hoskings has any motplats left? Dave V. Shiftless in CT ... From: "Ron Sutton"...
Dave before buying a motoplat ... that MZb ignition might be the way to go .. new technology plus lighting coil... Rico on the Vinduro board could give you...
... Dave, The parts are Dyna, I'll get a list and a wiring diagram together if you guys are interested. I'm also looking into getting a kit together and...
BT, ... From the pictures of the MZb ignitions that I've seen it maybe a problem hooking up and aligning the recoil starter pulley to the MZb flywheel. Another...
Thanks to everyone for their help. I have checked the drain in the bottom of the cylinder. No luck there. Then Friday morning I gave it a yank and it fired...
Ted, glad to hear you rode it!!!! It sounds like a similar problem I had until I replaced the coil on the ignition. I got a new one from denniskirk.com. Its...
Ted, I had a similar problem on one of my RT's, turned out to be a sticky needle and float.... Dave V. shiftless in CT ... From: <digitmstr@...> To:...
Hi Folks, I have a RTII 1976. The gas tank petcock is wore out and I cannot shut the gas flow off. The petcock is the type that you have to pull/push a button...
Your Name
slmchanz@...
Jul 26, 2004 4:16 pm
3061
Steve B. A replacement Petcock is available right from the factory. It'll be the new 90deg turn style. Just tell 'em you need it for a "trailbreaker" not and...
Mr Viebay do you have the Replacement part number for the new petcock and I will add to the Rokon parts interchange....I would like to make this change over if...
Sorry Brian I don't. Mark Johnson was the gentleman from the factory with the two new Rokons at the reunion ride and that's the info he gave. the ones I got...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
